camera/device/3.8/ICameraDevice.hal

/*
 * Copyright (C) 2021 The Android Open Source Project
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *      http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */

package android.hardware.camera.device@3.8;

import android.hardware.camera.common@1.0::Status;
import @3.7::ICameraDevice;

/**
 * Camera device interface
 *
 * Supports the android.hardware.Camera API, and the android.hardware.camera2
 * API at LIMITED or better hardware level.
 *
 * ICameraDevice.open() must return @3.2::ICameraDeviceSession,
 * @3.5::ICameraDeviceSession, @3.6::ICameraDeviceSession,
 * @3.7::ICameraDeviceSession, or @3.8::ICameraDeviceSession.
 */
interface ICameraDevice extends @3.7::ICameraDevice {
    /**
     * turnOnTorchWithStrengthLevel:
     *
     * Change the brightness level of the flash unit associated with this camera device
     * and set it to value in torchStrength. This function also turns ON the torch
     * with specified torchStrength if the torch is OFF.
     *
     * The torchStrength value must be within the valid range i.e. >=1 and
     * <= FLASH_INFO_STRENGTH_MAXIMUM_LEVEL. Whenever the torch is turned OFF,
     * the brightness level will reset to FLASH_INFO_STRENGTH_DEFAULT_LEVEL.
     * When the client calls setTorchMode(ON) after turnOnTorchWithStrengthLevel(N),
     * the flash unit will have brightness level equal to N. This level does not
     * represent the real brightness units. It is linear in nature i.e. flashlight
     * at level 10 is twice as bright as at level 5.
     *
     * @param torchStrength Brightness level to be set for the flashlight.
     *
     * @return status Status code for the operation, one of:
     *     OK:
     *         On a successful change to the torch strength level.
     *     INTERNAL_ERROR:
     *         The flash unit cannot be operated due to an unexpected internal
     *         error.
     *     CAMERA_IN_USE:
     *         This status code is returned when:
     *           - This camera device has been opened, so the torch cannot be
     *             controlled until it is closed.
     *           - Due to other camera devices being open, or due to other
     *             resource constraints, the torch cannot be controlled currently.
     *     ILLEGAL_ARGUMENT:
     *         If the torchStrength value is not within the range i.e. < 1 or
     *         > FLASH_INFO_STRENGTH_MAXIMUM_LEVEL.
     *     METHOD_NOT_SUPPORTED:
     *         This status code is returned when:
     *           - This camera device does not support direct operation of flashlight
     *             torch mode. The framework must open the camera device and turn
     *             the torch on through the device interface.
     *           - This camera device does not have a flash unit.
     *           - This camera device has flash unit but does not support torch
     *             strength control.
     *     CAMERA_DISCONNECTED:
     *         An external camera device has been disconnected, and is no longer
     *         available. This camera device interface is now stale, and a new
     *         instance must be acquired if the device is reconnected. All
     *         subsequent calls on this interface must return
     *         CAMERA_DISCONNECTED.
     *
     */
    turnOnTorchWithStrengthLevel(int32_t torchStrength) generates (Status status);

    /**
     * getTorchStrengthLevel:
     *
     * Get current torch strength level.
     * If the device supports torch strength control, when the torch is OFF the
     * strength level will reset to default level, so the return
     * value in this case will be equal to FLASH_INFO_STRENGTH_DEFAULT_LEVEL.
     *
     * @return status Status code for the operation, one of:
     *      OK:
     *           On success.
     *      INTERNAL_ERROR:
     *           An unexpected error occurred and the information is not
     *           available.
     *      METHOD_NOT_SUPPORTED:
     *          This status code is returned when:
     *            - This camera device does not support direct operation of flashlight
     *              torch mode. The framework must open the camera device and turn
     *              the torch on through the device interface.
     *            - This camera device does not have a flash unit.
     *            - This camera device has flash unit but does not support torch
     *              strength control.
     *
     * @return torchStrength Current torch strength level.
     *
     */
    getTorchStrengthLevel() generates (Status status, int32_t torchStrength);

     /**
     * isStreamCombinationSupported_3_8:
     *
     * Identical to @3.7::ICameraDevice.isStreamCombinationSupported, except
     * that it takes a @3.8::StreamConfiguration parameter, which could contain
     * additional information about a specific 10-bit dynamic range profile or
     * stream use case.
     *
     */
    isStreamCombinationSupported_3_8(StreamConfiguration streams)
            generates (Status status, bool queryStatus);
};