include/hardware/sensors.h

/*
 * Copyright (C) 2008 The Android Open Source Project
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *      http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */

#ifndef ANDROID_SENSORS_INTERFACE_H
#define ANDROID_SENSORS_INTERFACE_H

#include <stdint.h>
#include <sys/cdefs.h>
#include <sys/types.h>

#include <hardware/hardware.h>

__BEGIN_DECLS

/**
 * The id of this module
 */
#define SENSORS_HARDWARE_MODULE_ID "sensors"

/**
 * Name of the sensors device to open
 */
#define SENSORS_HARDWARE_CONTROL    "control"
#define SENSORS_HARDWARE_DATA       "data"

/**
 * Handles must be higher than SENSORS_HANDLE_BASE
 */
#define SENSORS_HANDLE_BASE             0
#define SENSORS_HANDLE_BITS             8
#define SENSORS_HANDLE_COUNT            (1<<SENSORS_HANDLE_BITS)


/**
 * Sensor types
 */
#define SENSOR_TYPE_ACCELEROMETER       1
#define SENSOR_TYPE_MAGNETIC_FIELD      2
#define SENSOR_TYPE_ORIENTATION         3
#define SENSOR_TYPE_GYROSCOPE           4
#define SENSOR_TYPE_LIGHT               5
#define SENSOR_TYPE_PRESSURE            6
#define SENSOR_TYPE_TEMPERATURE         7
#define SENSOR_TYPE_PROXIMITY           8

/**
 * Values returned by the accelerometer in various locations in the universe.
 * all values are in SI units (m/s^2)
 */

#define GRAVITY_SUN             (275.0f)
#define GRAVITY_MERCURY         (3.70f)
#define GRAVITY_VENUS           (8.87f)
#define GRAVITY_EARTH           (9.80665f)
#define GRAVITY_MOON            (1.6f)
#define GRAVITY_MARS            (3.71f)
#define GRAVITY_JUPITER         (23.12f)
#define GRAVITY_SATURN          (8.96f)
#define GRAVITY_URANUS          (8.69f)
#define GRAVITY_NEPTUNE         (11.0f)
#define GRAVITY_PLUTO           (0.6f)
#define GRAVITY_DEATH_STAR_I    (0.000000353036145f)
#define GRAVITY_THE_ISLAND      (4.815162342f)

/** Maximum magnetic field on Earth's surface */
#define MAGNETIC_FIELD_EARTH_MAX    (60.0f)

/** Minimum magnetic field on Earth's surface */
#define MAGNETIC_FIELD_EARTH_MIN    (30.0f)


/**
 * status of each sensor
 */

#define SENSOR_STATUS_UNRELIABLE        0
#define SENSOR_STATUS_ACCURACY_LOW      1
#define SENSOR_STATUS_ACCURACY_MEDIUM   2
#define SENSOR_STATUS_ACCURACY_HIGH     3

/**
 * Definition of the axis
 * ----------------------
 *
 * This API is relative to the screen of the device in its default orientation,
 * that is, if the device can be used in portrait or landscape, this API
 * is only relative to the NATURAL orientation of the screen. In other words,
 * the axis are not swapped when the device's screen orientation changes.
 * Higher level services /may/ perform this transformation.
 *
 *   x<0         x>0
 *                ^
 *                |
 *    +-----------+-->  y>0
 *    |           |
 *    |           |
 *    |           |
 *    |           |   / z<0
 *    |           |  /
 *    |           | /
 *    O-----------+/
 *    |[]  [ ]  []/
 *    +----------/+     y<0
 *              /
 *             /
 *           |/ z>0 (toward the sky)
 *
 *    O: Origin (x=0,y=0,z=0)
 *
 *
 * Orientation
 * ----------- 
 * 
 * All values are angles in degrees.
 * 
 * azimuth: angle between the magnetic north direction and the Y axis, around 
 *  the Z axis (0<=azimuth<360).
 *      0=North, 90=East, 180=South, 270=West
 * 
 * pitch: Rotation around X axis (-180<=pitch<=180), with positive values when
 *  the z-axis moves toward the y-axis.
 *
 * roll: Rotation around Y axis (-90<=roll<=90), with positive values when
 *  the z-axis moves AWAY from the x-axis.
 * 
 * Note: This definition is different from yaw, pitch and roll used in aviation
 *  where the X axis is along the long side of the plane (tail to nose).
 *  
 *  
 * Acceleration
 * ------------
 *
 *  All values are in SI units (m/s^2) and measure the acceleration of the
 *  device minus the force of gravity.
 *  
 *  x: Acceleration minus Gx on the x-axis 
 *  y: Acceleration minus Gy on the y-axis 
 *  z: Acceleration minus Gz on the z-axis
 *  
 *  Examples:
 *    When the device lies flat on a table and is pushed on its left side
 *    toward the right, the x acceleration value is positive.
 *    
 *    When the device lies flat on a table, the acceleration value is +9.81,
 *    which correspond to the acceleration of the device (0 m/s^2) minus the
 *    force of gravity (-9.81 m/s^2).
 *    
 *    When the device lies flat on a table and is pushed toward the sky, the
 *    acceleration value is greater than +9.81, which correspond to the
 *    acceleration of the device (+A m/s^2) minus the force of 
 *    gravity (-9.81 m/s^2).
 *    
 *    
 * Magnetic Field
 * --------------
 * 
 *  All values are in micro-Tesla (uT) and measure the ambient magnetic
 *  field in the X, Y and Z axis.
 *    
 */
typedef struct {
    union {
        float v[3];
        struct {
            float x;
            float y;
            float z;
        };
        struct {
            float azimuth;
            float pitch;
            float roll;
        };
    };
    int8_t status;
    uint8_t reserved[3];
} sensors_vec_t;

/**
 * Union of the various types of sensor data
 * that can be returned.
 */
typedef struct {
    /* sensor identifier */
    int             sensor;

    union {
        /* x,y,z values of the given sensor */
        sensors_vec_t   vector;

        /* orientation values are in degrees */
        sensors_vec_t   orientation;

        /* acceleration values are in meter per second per second (m/s^2) */
        sensors_vec_t   acceleration;

        /* magnetic vector values are in micro-Tesla (uT) */
        sensors_vec_t   magnetic;

        /* temperature is in degrees centigrade (Celsius) */
        float           temperature;
    };

    /* time is in nanosecond */
    int64_t         time;

    uint32_t        reserved;
} sensors_data_t;


struct sensor_t;

/**
 * Every hardware module must have a data structure named HAL_MODULE_INFO_SYM
 * and the fields of this data structure must begin with hw_module_t
 * followed by module specific information.
 */
struct sensors_module_t {
    struct hw_module_t common;

    /**
     * @return bit map of available sensors defined by
     *         the constants SENSORS_XXXX.
     */
    int (*get_sensors_list)(struct sensors_module_t* module,
            struct sensor_t const**);
};

struct sensor_t {
    const char*     name;
    const char*     vendor;
    int             version;
    int             handle;
    int             type;
    float           maxRange;
    float           resolution;
    float           power;
    void*           reserved[9];
};


/**
 * Every device data structure must begin with hw_device_t
 * followed by module specific public methods and attributes.
 */
struct sensors_control_device_t {
    struct hw_device_t common;
    
    /**
     * Returns the fd which will be the parameter to
     * sensors_data_device_t::open_data(). 
     * The caller takes ownership of this fd. This is intended to be
     * passed cross processes.
     *
     * @return a fd if successful, < 0 on error
     */
    int (*open_data_source)(struct sensors_control_device_t *dev);
    
    /** Activate/deactivate one or more of the sensors.
     *
     * @param sensors is the handle of the sensors to change.
     * @param enabled set to 1 to enable, or 0 to disable the sensor.
     *
     * @return 0 on success, negative errno code otherwise
     */
    int (*activate)(struct sensors_control_device_t *dev, 
            int handle, int enabled);
    
    /**
     * Set the delay between sensor events in ms
     *
     * @return 0 if successful, < 0 on error
     */
    int (*set_delay)(struct sensors_control_device_t *dev, int32_t ms);

    /**
     * Causes sensors_data_device_t.poll() to return -EWOULDBLOCK immediately.
     */
    int (*wake)(struct sensors_control_device_t *dev);
};

struct sensors_data_device_t {
    struct hw_device_t common;

    /**
     * Prepare to read sensor data.
     *
     * This routine does NOT take ownership of the fd
     * and must not close it. Typically this routine would
     * use a duplicate of the fd parameter.
     *
     * @param fd from sensors_control_open.
     *
     * @return 0 if successful, < 0 on error
     */
    int (*data_open)(struct sensors_data_device_t *dev, int fd);
    
    /**
     * Caller has completed using the sensor data.
     * The caller will not be blocked in sensors_data_poll
     * when this routine is called.
     *
     * @return 0 if successful, < 0 on error
     */
    int (*data_close)(struct sensors_data_device_t *dev);
    
    /**
     * Return sensor data for one of the enabled sensors.
     *
     * @return sensor handle for the returned data, 0x7FFFFFFF when 
     * sensors_control_device_t.wake() is called and -errno on error
     *  
     */
    int (*poll)(struct sensors_data_device_t *dev, 
            sensors_data_t* data);
};


/** convenience API for opening and closing a device */

static inline int sensors_control_open(const struct hw_module_t* module, 
        struct sensors_control_device_t** device) {
    return module->methods->open(module, 
            SENSORS_HARDWARE_CONTROL, (struct hw_device_t**)device);
}

static inline int sensors_control_close(struct sensors_control_device_t* device) {
    return device->common.close(&device->common);
}

static inline int sensors_data_open(const struct hw_module_t* module, 
        struct sensors_data_device_t** device) {
    return module->methods->open(module, 
            SENSORS_HARDWARE_DATA, (struct hw_device_t**)device);
}

static inline int sensors_data_close(struct sensors_data_device_t* device) {
    return device->common.close(&device->common);
}


__END_DECLS

#endif  // ANDROID_SENSORS_INTERFACE_H