diff --git a/include/hardware/context_hub.h b/include/hardware/context_hub.h
index 99756cb..828f2dd 100644
--- a/include/hardware/context_hub.h
+++ b/include/hardware/context_hub.h
@@ -358,6 +358,27 @@
  */
 
 /**
+ * CONTEXT_HUB_OS_REBOOT
+ * Reboots context hub OS, restarts all the nanoApps.
+ * No reboot notification is sent to nanoApps; reboot happens immediately and
+ * unconditionally; all volatile FW state and any data is lost as a result
+ *
+ * Payload : none
+ *
+ * Response : status_response_t
+ *            On receipt of a successful response, it is
+ *               expected that
+ *
+ *               i) system reboot has completed;
+ *                  status contains reboot reason code (platform-specific)
+ *
+ * Unsolicited response:
+ *            System may send unsolicited response at any time;
+ *            this should be interpreted as FW reboot, and necessary setup
+ *            has to be done (same or similar to the setup done on system boot)
+ */
+
+/**
  * All communication between the context hubs and the Context Hub Service is in
  * the form of messages. Some message types are distinguished and their
  * Semantics shall be well defined.
@@ -372,6 +393,7 @@
     CONTEXT_HUB_UNLOAD_APP   = 4, // Unload a specified app
     CONTEXT_HUB_QUERY_APPS   = 5, // Query for app(s) info on hub
     CONTEXT_HUB_QUERY_MEMORY = 6, // Query for memory info
+    CONTEXT_HUB_OS_REBOOT    = 7, // Request to reboot context HUB OS
 } hub_messages_e;
 
 #define CONTEXT_HUB_TYPE_PRIVATE_MSG_BASE 0x00400
diff --git a/include/hardware/vehicle.h b/include/hardware/vehicle.h
index ac7e470..da11407 100644
--- a/include/hardware/vehicle.h
+++ b/include/hardware/vehicle.h
@@ -253,7 +253,7 @@
 
 
 
- //==== HVAC Properties ====
+//==== HVAC Properties ====
 
 /**
  * Fan speed setting
@@ -383,6 +383,24 @@
 #define VEHICLE_PROPERTY_HVAC_AUTO_ON                               (0x0000050A)
 
 /**
+ * Seat temperature
+ *
+ * Negative values indicate cooling.
+ * 0 indicates off.
+ * Positive values indicate heating.
+ *
+ * Some vehicles may have multiple levels of heating and cooling. The min/max
+ * range defines the allowable range and number of steps in each direction.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_HVAC_SEAT_TEMPERATURE                      (0x0000050B)
+
+/**
  * Represents power state for HVAC. Some HVAC properties will require matching power to be turned on
  * to get out of OFF state. For non-zoned HVAC properties, VEHICLE_ALL_ZONE corresponds to
  * global power state.
@@ -653,6 +671,8 @@
     VEHICLE_AUDIO_CONTEXT_SYSTEM_SOUND_FLAG               = 0x400,
     /** Radio is played */
     VEHICLE_AUDIO_CONTEXT_RADIO_FLAG                      = 0x800,
+    /** Ext source is played. This is for tagging generic ext sources. */
+    VEHICLE_AUDIO_CONTEXT_EXT_SOURCE_FLAG                 = 0x1000,
 };
 
 /**
@@ -702,6 +722,11 @@
      * of each physical streams whenever there is an audio context change.
      */
     VEHICLE_AUDIO_VOLUME_CAPABILITY_PERSISTENT_STORAGE = 0x1,
+    /**
+     * When this flag is set, the H/W can support only single master volume for all streams.
+     * There is no way to set volume level differently per each stream or context.
+     */
+    VEHICLE_AUDIO_VOLUME_CAPABILITY_MASTER_VOLUME_ONLY = 0x2,
 };
 
 
@@ -821,6 +846,70 @@
     VEHICLE_AUDIO_HW_VARIANT_FLAG_INTERNAL_RADIO_FLAG = 0x1,
 };
 
+/** audio routing for AM/FM. This should be also be the value when there is only one
+    radio module in the system. */
+#define VEHICLE_PROPERTY_AUDIO_EXT_ROUTING_SOURCE_RADIO_AM_FM "RADIO_AM_FM"
+/** Should be added only when there is a separate radio module with HD capability. */
+#define VEHICLE_PROPERTY_AUDIO_EXT_ROUTING_SOURCE_RADIO_AM_FM_HD "RADIO_AM_FM_HD"
+/** For digial audio broadcasting type of radio */
+#define VEHICLE_PROPERTY_AUDIO_EXT_ROUTING_SOURCE_RADIO_DAB "RADIO_DAB"
+/** For satellite type of radio */
+#define VEHICLE_PROPERTY_AUDIO_EXT_ROUTING_SOURCE_RADIO_SATELLITE "RADIO_SATELLITE"
+/** For CD or DVD */
+#define VEHICLE_PROPERTY_AUDIO_EXT_ROUTING_SOURCE_CD_DVD "CD_DVD"
+/** For 1st auxiliary input */
+#define VEHICLE_PROPERTY_AUDIO_EXT_ROUTING_SOURCE_AUX_IN0 "AUX_IN0"
+/** For 2nd auxiliary input */
+#define VEHICLE_PROPERTY_AUDIO_EXT_ROUTING_SOURCE_AUX_IN1 "AUX_IN1"
+/** For navigation guidance from outside android */
+#define VEHICLE_PROPERTY_AUDIO_EXT_ROUTING_SOURCE_EXT_NAV_GUIDANCE "EXT_NAV_GUIDANCE"
+/** For voice command from outside android */
+#define VEHICLE_PROPERTY_AUDIO_EXT_ROUTING_SOURCE_EXT_VOICE_COMMAND "EXT_VOICE_COMMAND"
+/** For voice call from outside android */
+#define VEHICLE_PROPERTY_AUDIO_EXT_ROUTING_SOURCE_EXT_VOICE_CALL "EXT_VOICE_CALL"
+/** For safety alert from outside android */
+#define VEHICLE_PROPERTY_AUDIO_EXT_ROUTING_SOURCE_EXT_SAFETY_ALERT "EXT_SAFETY_ALERT"
+
+/**
+* Property to pass hint on external audio routing. When android side request focus
+* with VEHICLE_AUDIO_EXT_FOCUS_CAR_PLAY_ONLY_FLAG flag, this property will be set
+* before setting AUDIO_FOCUS property as a hint for external audio source routing.
+* Note that setting this property alone should not trigger any change.
+* Audio routing should be changed only when AUDIO_FOCUS property is set. Note that
+* this property allows passing custom value as long as it is defined in config_string.
+* This allows supporting non-standard routing options through this property.
+* It is recommended to use separate name space for custom property to prevent conflict in future
+* android releases.
+* Enabling each external routing option is done by enabling each bit flag for the routing.
+* This property can support up to 128 external routings.
+* To give full flexibility, there is no standard definition for each bit flag and
+* assigning each big flag to specific routing type is decided by config_string.
+* config_string has format of each entry separated by ','
+* and each entry has format of bitFlagPositon:typeString[:physicalStreamNumber].
+*  bitFlagPosition: represents which big flag will be set to enable this routing. 0 means
+*    LSB in int32_array[0]. 31 will be MSB in int32_array[0]. 127 will MSB in int32_array[3].
+*  typeString: string representation of external routing. Some types are already defined
+*    in VEHICLE_PROPERTY_AUDIO_EXT_ROUTING_SOURCE_* and use them first before adding something
+*    custom. Applications will find each routing using this string.
+*  physicalStreamNumber: This part is optional and represents physical stream to android
+*    which will be disabled when this routing is enabled. If not specified, this routing
+*    should not affect physical streams to android.
+* As an example, let's assume a system with two physical streams, 0 for media and 1 for
+* nav guidance. And let's assume external routing option of am fm radio, external navigation
+* guidance, satellite radio, and one custom. Let's assume that radio and satellite replaces
+* physical stream 0 and external navigation replaces physical stream 1. And bit flag will be
+* assigned in the order listed above. This configuration will look like this in config_string:
+*  "0:RADIO_AM_FM:0,1:EXT_NAV_GUIDANCE:1,2:RADIO_SATELLITE:0,3:com.test.SOMETHING_CUSTOM"
+* When android requests RADIO_AM_FM, int32_array[0] will be set to 0x1.
+* When android requests RADIO_SATELLITE + EXT_NAV_GUIDANCE, int32_array[0] will be set to 0x2|0x4.
+*
+* @value_type VEHICLE_VALUE_TYPE_INT32_VEC4
+* @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+* @access VEHICLE_PROP_ACCESS_WRITE|VEHICLE_PROP_ACCESS_READ_WRITE
+* @config_string List of all avaiable external source in the system.
+* @data_member int32_array
+*/
+#define VEHICLE_PROPERTY_AUDIO_EXT_ROUTING_HINT                     (0x00000905)
 
 /**
  * Property to control power state of application processor.
@@ -1098,26 +1187,158 @@
  */
 #define VEHICLE_PROPERTY_CURRENT_TIME_IN_SECONDS                    (0x00000A31)
 
+
+//==== Car Cabin Properties ====
 /**
- * Seat temperature
+ * Most Car Cabin properties have both a MOVE and POSITION parameter associated with them.
  *
- * Negative values indicate cooling.
- * 0 indicates off.
- * Positive values indicate heating.
+ * The MOVE parameter will start moving the device in the indicated direction.  The magnitude
+ * indicates the relative speed.  For instance, setting the WINDOW_MOVE parameter to +1 will roll
+ * the window up.  Setting it to +2 (if available) will roll it up faster.
  *
- * Some vehicles may have multiple levels of heating and cooling. The min/max
- * range defines the allowable range and number of steps in each direction.
+ * The POSITION parameter will move the device to the desired position.  For instance, if the
+ * WINDOW_POS has a range of 0-100, then setting this parameter to 50 will open the window halfway.
+ * Depending upon the initial position, the window may move up or down to the 50% value.
+ *
+ * OEMs may choose to implement one or both of the MOVE/POSITION parameters depending upon the
+ * capability of the hardware.
+ */
+
+// Doors
+/**
+ * Door position
+ *
+ * This is an integer in case a door may be set to a particular position.  Max
+ * value indicates fully open, min value (0) indicates fully closed.
+ *
+ * Some vehicles (minivans) can open the door electronically.  Hence, the ability
+ * to write this property.
  *
  * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
  * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
- * @access VEHICLE_PROP_ACCESS_WRITE
- * @zone_type VEHICLE_SEAT
+ * @access VEHICLE_PROP_ACCESS_READ|VEHICLE_PROP_ACCESS_WRITE
+ * @zone_type VEHICLE_DOOR
  * @data_member int32_value
  */
-#define VEHICLE_PROPERTY_SEAT_TEMPERATURE                           (0x00000B00)
+#define VEHICLE_PROPERTY_DOOR_POS                                   (0x00000B00)
 
 /**
- * Seat memory
+ * Door move
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE|VEHICLE_PROP_ACCESS_WRITE
+ * @zone_type VEHICLE_DOOR
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_DOOR_MOVE                                  (0x00000B01)
+
+
+/**
+ * Door lock
+ *
+ * 'true' indicates door is locked
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_BOOLEAN
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @zone_type VEHICLE_DOOR
+ * @data_member boolean_value
+ */
+#define VEHICLE_PROPERTY_DOOR_LOCK                                  (0x00000B02)
+
+// Mirrors
+/**
+ * Mirror Z Position
+ *
+ * Positive value indicates tilt upwards, negative value is downwards
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @zone_type VEHICLE_MIRROR
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_MIRROR_Z_POS                               (0x00000B40)
+
+/**
+ * Mirror Z Move
+ *
+ * Positive value indicates tilt upwards, negative value is downwards
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE|VEHICLE_PROP_ACCESS_WRITE
+ * @zone_type VEHICLE_MIRROR
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_MIRROR_Z_MOVE                              (0x00000B41)
+
+/**
+ * Mirror Y Position
+ *
+ * Positive value indicate tilt right, negative value is left
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @zone_type VEHICLE_MIRROR
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_MIRROR_Y_POS                               (0x00000B42)
+
+/**
+ * Mirror Y Move
+ *
+ * Positive value indicate tilt right, negative value is left
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE|VEHICLE_PROP_ACCESS_WRITE
+ * @zone_type VEHICLE_MIRROR
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_MIRROR_Y_MOVE                              (0x00000B43)
+
+/**
+ * Mirror Lock
+ *
+ * True indicates mirror positions are locked and not changeable
+ *
+ * @value_type VEHICLE_VALUE_TYPE_BOOLEAN
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @data_member boolean_value
+ */
+#define VEHICLE_PROPERTY_MIRROR_LOCK                                (0x00000B44)
+
+/**
+ * Mirror Heat
+ *
+ * Increase values denote higher heating levels.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_MIRROR_HEAT                                (0x00000B45)
+
+/**
+ * Mirror Fold
+ *
+ * True indicates mirrors are folded
+ *
+ * @value_type VEHICLE_VALUE_TYPE_BOOLEAN
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @data_member boolean_value
+ */
+#define VEHICLE_PROPERTY_MIRROR_FOLD                                (0x00000B46)
+
+// Seats
+/**
+ * Seat memory select
  *
  * This parameter selects the memory preset to use to select the seat position.
  * The minValue is always 0, and the maxValue determines the number of seat
@@ -1133,7 +1354,7 @@
  * @zone_type VEHICLE_SEAT
  * @data_member int32_value
  */
-#define VEHICLE_PROPERTY_SEAT_MEMORY_SELECT                         (0x00000B01)
+#define VEHICLE_PROPERTY_SEAT_MEMORY_SELECT                         (0x00000B80)
 
 /**
  * Seat memory set
@@ -1148,7 +1369,422 @@
  * @zone_type VEHICLE_SEAT
  * @data_member int32_value
  */
-#define VEHICLE_PROPERTY_SEAT_MEMORY_SET                            (0x00000B02)
+#define VEHICLE_PROPERTY_SEAT_MEMORY_SET                            (0x00000B81)
+
+/**
+ * Seatbelt buckled
+ *
+ * True indicates belt is buckled.
+ *
+ * Write access indicates automatic seat buckling capabilities.  There are no known cars at this
+ * time, but you never know...
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_BOOLEAN
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ|VEHICLE_PROP_ACCESS_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member boolean_value
+ */
+#define VEHICLE_PROPERTY_SEAT_BELT_BUCKLED                          (0x00000B82)
+
+/**
+ * Seatbelt height position
+ *
+ * Adjusts the shoulder belt anchor point.
+ * Max value indicates highest position
+ * Min value indicates lowest position
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_BELT_HEIGHT_POS                       (0x00000B83)
+
+/**
+ * Seatbelt height move
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE|VEHICLE_PROP_ACCESS_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_BELT_HEIGHT_MOVE                      (0x00000B84)
+
+/**
+ * Seat fore/aft position
+ *
+ * Sets the seat position forward (closer to steering wheel) and backwards.
+ * Max value indicates closest to wheel, min value indicates most rearward
+ * position.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_FORE_AFT_POS                          (0x00000B85)
+
+/**
+ * Seat fore/aft move
+ *
+ * Moves the seat position forward and aft.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE|VEHICLE_PROP_ACCESS_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_FORE_AFT_MOVE                         (0x00000B86)
+
+/**
+ * Seat backrest angle 1 position
+ *
+ * Backrest angle 1 is the actuator closest to the bottom of the seat.
+ * Max value indicates angling forward towards the steering wheel.
+ * Min value indicates full recline.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_BACKREST_ANGLE_1_POS                  (0x00000B87)
+
+/**
+ * Seat backrest angle 1 move
+ *
+ * Moves the backrest forward or recline.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE|VEHICLE_PROP_ACCESS_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_BACKREST_ANGLE_1_MOVE                 (0x00000B88)
+
+/**
+ * Seat backrest angle 2 position
+ *
+ * Backrest angle 2 is the next actuator up from the bottom of the seat.
+ * Max value indicates angling forward towards the steering wheel.
+ * Min value indicates full recline.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_BACKREST_ANGLE_2_POS                  (0x00000B89)
+
+/**
+ * Seat backrest angle 2 move
+ *
+ * Moves the backrest forward or recline.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE|VEHICLE_PROP_ACCESS_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_BACKREST_ANGLE_2_MOVE                 (0x00000B8A)
+
+/**
+ * Seat height position
+ *
+ * Sets the seat height.
+ * Max value indicates highest position.
+ * Min value indicates lowest position.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_HEIGHT_POS                            (0x00000B8B)
+
+/**
+ * Seat height move
+ *
+ * Moves the seat height.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE|VEHICLE_PROP_ACCESS_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_HEIGHT_MOVE                           (0x00000B8C)
+
+/**
+ * Seat depth position
+ *
+ * Sets the seat depth, distance from back rest to front edge of seat.
+ * Max value indicates longest depth position.
+ * Min value indicates shortest position.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_DEPTH_POS                             (0x00000B8D)
+
+/**
+ * Seat depth move
+ *
+ * Adjusts the seat depth.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE|VEHICLE_PROP_ACCESS_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_DEPTH_MOVE                            (0x00000B8E)
+
+/**
+ * Seat tilt position
+ *
+ * Sets the seat tilt.
+ * Max value indicates front edge of seat higher than back edge.
+ * Min value indicates front edge of seat lower than back edge.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_TILT_POS                              (0x00000B8F)
+
+/**
+ * Seat tilt move
+ *
+ * Tilts the seat.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE|VEHICLE_PROP_ACCESS_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_TILT_MOVE                             (0x00000B90)
+
+/**
+ * Lumber fore/aft position
+ *
+ * Pushes the lumbar support forward and backwards
+ * Max value indicates most forward position.
+ * Min value indicates most rearward position.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_LUMBAR_FORE_AFT_POS                   (0x00000B91)
+
+/**
+ * Lumbar fore/aft move
+ *
+ * Adjusts the lumbar support.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE|VEHICLE_PROP_ACCESS_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_LUMBAR_FORE_AFT_MOVE                  (0x00000B92)
+
+/**
+ * Lumbar side support position
+ *
+ * Sets the amount of lateral lumbar support.
+ * Max value indicates widest lumbar setting (i.e. least support)
+ * Min value indicates thinnest lumbar setting.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_LUMBAR_SIDE_SUPPORT_POS               (0x00000B93)
+
+/**
+ * Lumbar side support move
+ *
+ * Adjusts the amount of lateral lumbar support.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE|VEHICLE_PROP_ACCESS_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_LUMBAR_SIDE_SUPPORT_MOVE              (0x00000B94)
+
+/**
+ * Headrest height position
+ *
+ * Sets the headrest height.
+ * Max value indicates tallest setting.
+ * Min value indicates shortest setting.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_HEADREST_HEIGHT_POS                   (0x00000B95)
+
+/**
+ * Headrest heigh move
+ *
+ * Moves the headrest up and down.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE|VEHICLE_PROP_ACCESS_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_HEADREST_HEIGHT_MOVE                  (0x00000B96)
+
+/**
+ * Headrest angle position
+ *
+ * Sets the angle of the headrest.
+ * Max value indicates most upright angle.
+ * Min value indicates shallowest headrest angle.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_HEADREST_ANGLE_POS                    (0x00000B97)
+
+/**
+ * Headrest angle move
+ *
+ * Adjusts the angle of the headrest
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE|VEHICLE_PROP_ACCESS_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_HEADREST_ANGLE_MOVE                   (0x00000B98)
+
+/**
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_HEADREST_FORE_AFT_POS                 (0x00000B99)
+
+/**
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE|VEHICLE_PROP_ACCESS_WRITE
+ * @zone_type VEHICLE_SEAT
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_SEAT_HEADREST_FORE_AFT_MOVE                (0x00000B9A)
+
+
+// Windows
+/**
+ * Window Position
+ *
+ * Max = window up / closed
+ * Min = window down / open
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_WINDOW_POS                                 (0x00000BC0)
+
+/**
+ * Window Move
+ *
+ * Max = window up / closed
+ * Min = window down / open
+ * Magnitude denotes relative speed.  I.e. +2 is faster than +1 in raising the window.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE|VEHICLE_PROP_ACCESS_WRITE
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_WINDOW_MOVE                                (0x00000BC1)
+
+/**
+ * Window Vent Position
+ *
+ * This feature is used to control the vent feature on a sunroof.
+ *
+ * Max = vent open
+ * Min = vent closed
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_WINDOW_VENT_POS                            (0x00000BC2)
+
+/**
+ * Window Vent Move
+ *
+ * This feature is used to control the vent feature on a sunroof.
+ *
+ * Max = vent open
+ * Min = vent closed
+ *
+ * @value_type VEHICLE_VALUE_TYPE_ZONED_INT32
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE|VEHICLE_PROP_ACCESS_WRITE
+ * @data_member int32_value
+ */
+#define VEHICLE_PROPERTY_WINDOW_VENT_MOVE                           (0x00000BC3)
+
+/**
+ * Window Lock
+ *
+ * True indicates windows are locked and can't be moved.
+ *
+ * @value_type VEHICLE_VALUE_TYPE_BOOLEAN
+ * @change_mode VEHICLE_PROP_CHANGE_MODE_ON_CHANGE
+ * @access VEHICLE_PROP_ACCESS_READ_WRITE
+ * @data_member boolean_value
+ */
+#define VEHICLE_PROPERTY_WINDOW_LOCK                                (0x00000BC4)
+
+
 
 /**
  *  H/W specific, non-standard property can be added as necessary. Such property should use
@@ -1240,7 +1876,7 @@
      * Property of this type will be reported when there is a change.
      * get call should return the current value.
      * Set operation for this property is assumed to be asynchronous. When the property is read
-     * (=get) after set, it may still return old value until underlying H/W backing this property
+     * (get) after set, it may still return old value until underlying H/W backing this property
      * has actually changed the state. Once state is changed, the property will dispatch changed
      * value as event.
      */
diff --git a/modules/input/evdev/InputHub.cpp b/modules/input/evdev/InputHub.cpp
index 389955d..e2c65fa 100644
--- a/modules/input/evdev/InputHub.cpp
+++ b/modules/input/evdev/InputHub.cpp
@@ -610,7 +610,7 @@
             for (;;) {
                 ssize_t readSize = TEMP_FAILURE_RETRY(read(inputFd, ievs, sizeof(ievs)));
                 if (readSize == 0 || (readSize < 0 && errno == ENODEV)) {
-                    ALOGW("could not get event, removed? (fd: %d, size: %d errno: %d)",
+                    ALOGW("could not get event, removed? (fd: %d, size: %zd errno: %d)",
                             inputFd, readSize, errno);
 
                     removedDeviceFds.push_back(inputFd);
@@ -621,7 +621,7 @@
                     }
                     break;
                 } else if (readSize % sizeof(input_event) != 0) {
-                    ALOGE("could not get event. wrong size=%d", readSize);
+                    ALOGE("could not get event. wrong size=%zd", readSize);
                     break;
                 } else {
                     size_t count = static_cast<size_t>(readSize) / sizeof(struct input_event);
@@ -702,7 +702,7 @@
             if (event->mask & IN_CREATE) {
                 auto deviceNode = openNode(path);
                 if (deviceNode == nullptr) {
-                    ALOGE("could not open device node %s. err=%d", path.c_str(), res);
+                    ALOGE("could not open device node %s. err=%zd", path.c_str(), res);
                 } else {
                     mInputCallback->onDeviceAdded(deviceNode);
                 }
diff --git a/modules/vehicle/vehicle.c b/modules/vehicle/vehicle.c
index 548ceb3..2d945fd 100644
--- a/modules/vehicle/vehicle.c
+++ b/modules/vehicle/vehicle.c
@@ -331,22 +331,6 @@
         event.prop = sub->prop;
         event.timestamp = elapsedRealtimeNano();
         switch (sub->prop) {
-            case VEHICLE_PROPERTY_DRIVING_STATUS:
-                event.value_type = VEHICLE_VALUE_TYPE_INT32;
-                switch ((event.timestamp & 0x30000000)>>28) {
-                    case 0:
-                        event.value.driving_status = VEHICLE_DRIVING_STATUS_UNRESTRICTED;
-                        break;
-                    case 1:
-                        event.value.driving_status = VEHICLE_DRIVING_STATUS_NO_VIDEO;
-                        break;
-                    case 2:
-                        event.value.driving_status = VEHICLE_DRIVING_STATUS_NO_KEYBOARD_INPUT;
-                        break;
-                    default:
-                        event.value.driving_status = VEHICLE_DRIVING_STATUS_NO_CONFIG;
-                }
-                break;
             case VEHICLE_PROPERTY_GEAR_SELECTION:
                 event.value_type = VEHICLE_VALUE_TYPE_INT32;
                 switch ((event.timestamp & 0x30000000)>>28) {