diff --git a/audio/7.0/IDevice.hal b/audio/7.0/IDevice.hal
new file mode 100644
index 0000000..7082d6b
--- /dev/null
+++ b/audio/7.0/IDevice.hal
@@ -0,0 +1,346 @@
+/*
+ * Copyright (C) 2020 The Android Open Source Project
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ *      http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+package android.hardware.audio@7.0;
+
+import android.hardware.audio.common@7.0;
+import IStreamIn;
+import IStreamOut;
+
+interface IDevice {
+    /**
+     * Returns whether the audio hardware interface has been initialized.
+     *
+     * @return retval OK on success, NOT_INITIALIZED on failure.
+     */
+    initCheck() generates (Result retval);
+
+    /**
+     * Sets the audio volume for all audio activities other than voice call. If
+     * NOT_SUPPORTED is returned, the software mixer will emulate this
+     * capability.
+     *
+     * @param volume 1.0f means unity, 0.0f is zero.
+     * @return retval operation completion status.
+     */
+    setMasterVolume(float volume) generates (Result retval);
+
+    /**
+     * Get the current master volume value for the HAL, if the HAL supports
+     * master volume control. For example, AudioFlinger will query this value
+     * from the primary audio HAL when the service starts and use the value for
+     * setting the initial master volume across all HALs. HALs which do not
+     * support this method must return NOT_SUPPORTED in 'retval'.
+     *
+     * @return retval operation completion status.
+     * @return volume 1.0f means unity, 0.0f is zero.
+     */
+    getMasterVolume() generates (Result retval, float volume);
+
+    /**
+     * Sets microphone muting state.
+     *
+     * @param mute whether microphone is muted.
+     * @return retval operation completion status.
+     */
+    setMicMute(bool mute) generates (Result retval);
+
+    /**
+     * Gets whether microphone is muted.
+     *
+     * @return retval operation completion status.
+     * @return mute whether microphone is muted.
+     */
+    getMicMute() generates (Result retval, bool mute);
+
+    /**
+     * Set the audio mute status for all audio activities. If the return value
+     * is NOT_SUPPORTED, the software mixer will emulate this capability.
+     *
+     * @param mute whether audio is muted.
+     * @return retval operation completion status.
+     */
+    setMasterMute(bool mute) generates (Result retval);
+
+    /**
+     * Get the current master mute status for the HAL, if the HAL supports
+     * master mute control. AudioFlinger will query this value from the primary
+     * audio HAL when the service starts and use the value for setting the
+     * initial master mute across all HALs. HAL must indicate that the feature
+     * is not supported by returning NOT_SUPPORTED status.
+     *
+     * @return retval operation completion status.
+     * @return mute whether audio is muted.
+     */
+    getMasterMute() generates (Result retval, bool mute);
+
+    /**
+     * Returns audio input buffer size according to parameters passed or
+     * INVALID_ARGUMENTS if one of the parameters is not supported.
+     *
+     * @param config audio configuration.
+     * @return retval operation completion status.
+     * @return bufferSize input buffer size in bytes.
+     */
+    getInputBufferSize(AudioConfig config)
+            generates (Result retval, uint64_t bufferSize);
+
+    /**
+     * This method creates and opens the audio hardware output stream.
+     * If the stream can not be opened with the proposed audio config,
+     * HAL must provide suggested values for the audio config.
+     *
+     * @param ioHandle handle assigned by AudioFlinger.
+     * @param device device type and (if needed) address.
+     * @param config stream configuration.
+     * @param flags additional flags.
+     * @param sourceMetadata Description of the audio that will be played.
+                             May be used by implementations to configure hardware effects.
+     * @return retval operation completion status.
+     * @return outStream created output stream.
+     * @return suggestedConfig in case of invalid parameters, suggested config.
+     */
+    openOutputStream(
+            AudioIoHandle ioHandle,
+            DeviceAddress device,
+            AudioConfig config,
+            bitfield<AudioOutputFlag> flags,
+            SourceMetadata sourceMetadata) generates (
+                    Result retval,
+                    IStreamOut outStream,
+                    AudioConfig suggestedConfig);
+
+    /**
+     * This method creates and opens the audio hardware input stream.
+     * If the stream can not be opened with the proposed audio config,
+     * HAL must provide suggested values for the audio config.
+     *
+     * @param ioHandle handle assigned by AudioFlinger.
+     * @param device device type and (if needed) address.
+     * @param config stream configuration.
+     * @param flags additional flags.
+     * @param sinkMetadata Description of the audio that is suggested by the client.
+     *                     May be used by implementations to configure processing effects.
+     * @return retval operation completion status.
+     * @return inStream in case of success, created input stream.
+     * @return suggestedConfig in case of invalid parameters, suggested config.
+     */
+    openInputStream(
+            AudioIoHandle ioHandle,
+            DeviceAddress device,
+            AudioConfig config,
+            bitfield<AudioInputFlag> flags,
+            SinkMetadata sinkMetadata) generates (
+                    Result retval,
+                    IStreamIn inStream,
+                    AudioConfig suggestedConfig);
+
+    /**
+     * Returns whether HAL supports audio patches. Patch represents a connection
+     * between signal source(s) and signal sink(s). If HAL doesn't support
+     * patches natively (in hardware) then audio system will need to establish
+     * them in software.
+     *
+     * @return supports true if audio patches are supported.
+     */
+    supportsAudioPatches() generates (bool supports);
+
+    /**
+     * Creates an audio patch between several source and sink ports.  The handle
+     * is allocated by the HAL and must be unique for this audio HAL module.
+     *
+     * @param sources patch sources.
+     * @param sinks patch sinks.
+     * @return retval operation completion status.
+     * @return patch created patch handle.
+     */
+    createAudioPatch(vec<AudioPortConfig> sources, vec<AudioPortConfig> sinks)
+            generates (Result retval, AudioPatchHandle patch);
+
+    /**
+     * Updates an audio patch.
+     *
+     * Use of this function is preferred to releasing and re-creating a patch
+     * as the HAL module can figure out a way of switching the route without
+     * causing audio disruption.
+     *
+     * @param previousPatch handle of the previous patch to update.
+     * @param sources new patch sources.
+     * @param sinks new patch sinks.
+     * @return retval operation completion status.
+     * @return patch updated patch handle.
+     */
+    updateAudioPatch(
+            AudioPatchHandle previousPatch,
+            vec<AudioPortConfig> sources,
+            vec<AudioPortConfig> sinks) generates (
+                    Result retval, AudioPatchHandle patch);
+
+    /**
+     * Release an audio patch.
+     *
+     * @param patch patch handle.
+     * @return retval operation completion status.
+     */
+    releaseAudioPatch(AudioPatchHandle patch) generates (Result retval);
+
+    /**
+     * Returns the list of supported attributes for a given audio port.
+     *
+     * As input, 'port' contains the information (type, role, address etc...)
+     * needed by the HAL to identify the port.
+     *
+     * As output, 'resultPort' contains possible attributes (sampling rates,
+     * formats, channel masks, gain controllers...) for this port.
+     *
+     * @param port port identifier.
+     * @return retval operation completion status.
+     * @return resultPort port descriptor with all parameters filled up.
+     */
+    getAudioPort(AudioPort port)
+            generates (Result retval, AudioPort resultPort);
+
+    /**
+     * Set audio port configuration.
+     *
+     * @param config audio port configuration.
+     * @return retval operation completion status.
+     */
+    setAudioPortConfig(AudioPortConfig config) generates (Result retval);
+
+    /**
+     * Gets the HW synchronization source of the device. Calling this method is
+     * equivalent to getting AUDIO_PARAMETER_HW_AV_SYNC on the legacy HAL.
+     * Optional method
+     *
+     * @return retval operation completion status: OK or NOT_SUPPORTED.
+     * @return hwAvSync HW synchronization source
+     */
+    getHwAvSync() generates (Result retval, AudioHwSync hwAvSync);
+
+    /**
+     * Sets whether the screen is on. Calling this method is equivalent to
+     * setting AUDIO_PARAMETER_KEY_SCREEN_STATE on the legacy HAL.
+     * Optional method
+     *
+     * @param turnedOn whether the screen is turned on.
+     * @return retval operation completion status.
+     */
+    setScreenState(bool turnedOn) generates (Result retval);
+
+    /**
+     * Generic method for retrieving vendor-specific parameter values.
+     * The framework does not interpret the parameters, they are passed
+     * in an opaque manner between a vendor application and HAL.
+     *
+     * Multiple parameters can be retrieved at the same time.
+     * The implementation should return as many requested parameters
+     * as possible, even if one or more is not supported
+     *
+     * @param context provides more information about the request
+     * @param keys keys of the requested parameters
+     * @return retval operation completion status.
+     *         OK must be returned if keys is empty.
+     *         NOT_SUPPORTED must be returned if at least one key is unknown.
+     * @return parameters parameter key value pairs.
+     *         Must contain the value of all requested keys if retval == OK
+     */
+    getParameters(vec<ParameterValue> context, vec<string> keys)
+            generates (Result retval, vec<ParameterValue> parameters);
+
+    /**
+     * Generic method for setting vendor-specific parameter values.
+     * The framework does not interpret the parameters, they are passed
+     * in an opaque manner between a vendor application and HAL.
+     *
+     * Multiple parameters can be set at the same time though this is
+     * discouraged as it make failure analysis harder.
+     *
+     * If possible, a failed setParameters should not impact the platform state.
+     *
+     * @param context provides more information about the request
+     * @param parameters parameter key value pairs.
+     * @return retval operation completion status.
+     *         All parameters must be successfully set for OK to be returned
+     */
+    setParameters(vec<ParameterValue> context, vec<ParameterValue> parameters)
+            generates (Result retval);
+
+    /**
+     * Returns an array with available microphones in device.
+     *
+     * @return retval NOT_SUPPORTED if there are no microphones on this device
+     *                INVALID_STATE if the call is not successful,
+     *                OK otherwise.
+     *
+     * @return microphones array with microphones info
+     */
+    getMicrophones()
+         generates(Result retval, vec<MicrophoneInfo> microphones);
+
+    /**
+     * Notifies the device module about the connection state of an input/output
+     * device attached to it. Calling this method is equivalent to setting
+     * AUDIO_PARAMETER_DEVICE_[DIS]CONNECT on the legacy HAL.
+     *
+     * @param address audio device specification.
+     * @param connected whether the device is connected.
+     * @return retval operation completion status.
+     */
+    setConnectedState(DeviceAddress address, bool connected)
+            generates (Result retval);
+
+    /**
+     * Called by the framework to deinitialize the device and free up
+     * all currently allocated resources. It is recommended to close
+     * the device on the client side as soon as it is becomes unused.
+     *
+     * Note that all streams must be closed by the client before
+     * attempting to close the device they belong to.
+     *
+     * @return retval OK in case the success.
+     *                INVALID_STATE if the device was already closed
+     *                or there are streams currently opened.
+     */
+    @exit
+    close() generates (Result retval);
+
+    /**
+     * Applies an audio effect to an audio device. The effect is inserted
+     * according to its insertion preference specified by INSERT_... EffectFlags
+     * in the EffectDescriptor.
+     *
+     * @param device identifies the sink or source device this effect must be applied to.
+     *               "device" is the AudioPortHandle indicated for the device when the audio
+     *                patch connecting that device was created.
+     * @param effectId effect ID (obtained from IEffectsFactory.createEffect) of
+     *                 the effect to add.
+     * @return retval operation completion status.
+     */
+    addDeviceEffect(AudioPortHandle device, uint64_t effectId) generates (Result retval);
+
+    /**
+     * Stops applying an audio effect to an audio device.
+     *
+     * @param device identifies the sink or source device this effect was applied to.
+     *               "device" is the AudioPortHandle indicated for the device when the audio
+     *               patch is created at the audio HAL.
+     * @param effectId effect ID (obtained from IEffectsFactory.createEffect) of
+     *                 the effect.
+     * @return retval operation completion status.
+     */
+    removeDeviceEffect(AudioPortHandle device, uint64_t effectId) generates (Result retval);
+};