diff --git a/hostapd/hostapd.conf b/hostapd/hostapd.conf
index 263a04e..812c09a 100644
--- a/hostapd/hostapd.conf
+++ b/hostapd/hostapd.conf
@@ -72,7 +72,7 @@
 # run as non-root users. However, since the control interface can be used to
 # change the network configuration, this access needs to be protected in many
 # cases. By default, hostapd is configured to use gid 0 (root). If you
-# want to allow non-root users to use the contron interface, add a new group
+# want to allow non-root users to use the control interface, add a new group
 # and change this value to match with that group. Add users that should have
 # control interface access to this group.
 #
@@ -598,8 +598,6 @@
 #	channels if needed or creation of 40 MHz channel maybe rejected based
 #	on overlapping BSSes. These changes are done automatically when hostapd
 #	is setting up the 40 MHz channel.
-# Spatial Multiplexing (SM) Power Save: [SMPS-STATIC] or [SMPS-DYNAMIC]
-#	(SMPS disabled if neither is set)
 # HT-greenfield: [GF] (disabled if not set)
 # Short GI for 20 MHz: [SHORT-GI-20] (disabled if not set)
 # Short GI for 40 MHz: [SHORT-GI-40] (disabled if not set)
@@ -806,6 +804,9 @@
 # he_bss_color: BSS color (1-63)
 #he_bss_color=1
 
+# he_bss_color_partial: BSS color AID equation
+#he_bss_color_partial=0
+
 #he_default_pe_duration: The duration of PE field in an HE PPDU in us
 # Possible values are 0 us (default), 4 us, 8 us, 12 us, and 16 us
 #he_default_pe_duration=0
@@ -903,6 +904,8 @@
 
 # EAP reauthentication period in seconds (default: 3600 seconds; 0 = disable
 # reauthentication).
+# Note: Reauthentications may enforce a disconnection, check the related
+# parameter wpa_deny_ptk0_rekey for details.
 #eap_reauth_period=3600
 
 # Use PAE group address (01:80:c2:00:00:03) instead of individual target
@@ -1507,6 +1510,17 @@
 # wpa_key_mgmt=SAE for WPA3-Personal instead of wpa_key_mgmt=WPA-PSK).
 #wpa=2
 
+# Extended Key ID support for Individually Addressed frames
+#
+# Extended Key ID allows to rekey PTK keys without the impacts the "normal"
+# PTK rekeying with only a single Key ID 0 has. It can only be used when the
+# driver supports it and RSN/WPA2 is used with a CCMP/GCMP pairwise cipher.
+#
+# 0 = force off, i.e., use only Key ID 0 (default)
+# 1 = enable and use Extended Key ID support when possible
+# 2 = identical to 1 but start with Key ID 1 when possible
+#extended_key_id=0
+
 # WPA pre-shared keys for WPA-PSK. This can be either entered as a 256-bit
 # secret in hex format (64 hex digits), wpa_psk, or as an ASCII passphrase
 # (8..63 characters) that will be converted to PSK. This conversion uses SSID
@@ -1607,8 +1621,26 @@
 
 # Maximum lifetime for PTK in seconds. This can be used to enforce rekeying of
 # PTK to mitigate some attacks against TKIP deficiencies.
+# Warning: PTK rekeying is buggy with many drivers/devices and with such
+# devices, the only secure method to rekey the PTK without Extended Key ID
+# support requires a disconnection. Check the related parameter
+# wpa_deny_ptk0_rekey for details.
 #wpa_ptk_rekey=600
 
+# Workaround for PTK rekey issues
+#
+# PTK0 rekeys (rekeying the PTK without "Extended Key ID for Individually
+# Addressed Frames") can degrade the security and stability with some cards.
+# To avoid such issues hostapd can replace those PTK rekeys (including EAP
+# reauthentications) with disconnects.
+#
+# Available options:
+# 0 = always rekey when configured/instructed (default)
+# 1 = only rekey when the local driver is explicitly indicating it can perform
+#	this operation without issues
+# 2 = never allow PTK0 rekeys
+#wpa_deny_ptk0_rekey=0
+
 # The number of times EAPOL-Key Message 1/4 and Message 3/4 in the RSN 4-Way
 # Handshake are retried per 4-Way Handshake attempt.
 # (dot11RSNAConfigPairwiseUpdateCount)
@@ -1677,6 +1709,12 @@
 # available in deployed devices.
 #group_mgmt_cipher=AES-128-CMAC
 
+# Beacon Protection (management frame protection for Beacon frames)
+# This depends on management frame protection being enabled (ieee80211w != 0).
+# 0 = disabled (default)
+# 1 = enabled
+#beacon_prot=0
+
 # Association SA Query maximum timeout (in TU = 1.024 ms; for MFP)
 # (maximum time to wait for a SA Query response)
 # dot11AssociationSAQueryMaximumTimeout, 1...4294967295
@@ -1784,11 +1822,13 @@
 #sae_confirm_immediate=0
 
 # SAE mechanism for PWE derivation
-# 0 = hunting-and-pecking loop only (default)
-# 1 = hash-to-element only
+# 0 = hunting-and-pecking loop only (default without password identifier)
+# 1 = hash-to-element only (default with password identifier)
 # 2 = both hunting-and-pecking loop and hash-to-element enabled
 # Note: The default value is likely to change from 0 to 2 once the new
 # hash-to-element mechanism has received more interoperability testing.
+# When using SAE password identifier, the hash-to-element mechanism is used
+# regardless of the sae_pwe parameter value.
 #sae_pwe=0
 
 # FILS Cache Identifier (16-bit value in hexdump format)
@@ -1815,6 +1855,19 @@
 # http://www.iana.org/assignments/ipsec-registry/ipsec-registry.xml#ipsec-registry-10
 #owe_groups=19 20 21
 
+# OWE PTK derivation workaround
+# Initial OWE implementation used SHA256 when deriving the PTK for all OWE
+# groups. This was supposed to change to SHA384 for group 20 and SHA512 for
+# group 21. This parameter can be used to enable workaround for interoperability
+# with stations that use SHA256 with groups 20 and 21. By default (0) only the
+# appropriate hash function is accepted. When workaround is enabled (1), the
+# appropriate hash function is tried first and if that fails, SHA256-based PTK
+# derivation is attempted. This workaround can result in reduced security for
+# groups 20 and 21, but is required for interoperability with older
+# implementations. There is no impact to group 19 behavior. The workaround is
+# disabled by default and can be enabled by uncommenting the following line.
+#owe_ptk_workaround=1
+
 # OWE transition mode configuration
 # Pointer to the matching open/OWE BSS
 #owe_transition_bssid=<bssid>
@@ -1852,6 +1905,23 @@
 # default: 30 TUs (= 30.72 milliseconds)
 #fils_hlp_wait_time=30
 
+# Transition Disable indication
+# The AP can notify authenticated stations to disable transition mode in their
+# network profiles when the network has completed transition steps, i.e., once
+# sufficiently large number of APs in the ESS have been updated to support the
+# more secure alternative. When this indication is used, the stations are
+# expected to automatically disable transition mode and less secure security
+# options. This includes use of WEP, TKIP (including use of TKIP as the group
+# cipher), and connections without PMF.
+# Bitmap bits:
+# bit 0 (0x01): WPA3-Personal (i.e., disable WPA2-Personal = WPA-PSK and only
+#	allow SAE to be used)
+# bit 1 (0x02): SAE-PK (disable SAE without use of SAE-PK)
+# bit 2 (0x04): WPA3-Enterprise (move to requiring PMF)
+# bit 3 (0x08): Enhanced Open (disable use of open network; require OWE)
+# (default: 0 = do not include Transition Disable KDE)
+#transition_disable=0x01
+
 ##### IEEE 802.11r configuration ##############################################
 
 # Mobility Domain identifier (dot11FTMobilityDomainID, MDID)
@@ -2205,6 +2275,13 @@
 #wps_nfc_dh_privkey: Hexdump of DH Private Key
 #wps_nfc_dev_pw: Hexdump of Device Password
 
+# Application Extension attribute for Beacon and Probe Response frames
+# This parameter can be used to add application extension into WPS IE. The
+# contents of this parameter starts with 16-octet (32 hexdump characters) of
+# UUID to identify the specific application and that is followed by the actual
+# application specific data.
+#wps_application_ext=<hexdump>
+
 ##### Wi-Fi Direct (P2P) ######################################################
 
 # Enable P2P Device management
@@ -2227,6 +2304,17 @@
 #dpp_csign
 #dpp_controller
 
+# Configurator Connectivity indication
+# 0: no Configurator is currently connected (default)
+# 1: advertise that a Configurator is available
+#dpp_configurator_connectivity=0
+
+# DPP PFS
+# 0: allow PFS to be used or not used (default)
+# 1: require PFS to be used (note: not compatible with DPP R1)
+# 2: do not allow PFS to be used
+#dpp_pfs=0
+
 #### TDLS (IEEE 802.11z-2010) #################################################
 
 # Prohibit use of TDLS in this BSS
@@ -2607,7 +2695,7 @@
 # Default is 0 = OCE disabled
 #oce=0
 
-# RSSI-based assocition rejection
+# RSSI-based association rejection
 #
 # Reject STA association if RSSI is below given threshold (in dBm)
 # Allowed range: -60 to -90 dBm; default = 0 (rejection disabled)