diff --git a/hostapd/hostapd.conf b/hostapd/hostapd.conf
index 1357649..f02cd92 100644
--- a/hostapd/hostapd.conf
+++ b/hostapd/hostapd.conf
@@ -980,22 +980,10 @@
 
 # 6 GHz Access Point type
 # This config is to set the 6 GHz Access Point type. Possible options are:
-# 0 = Indoor AP
-# 1 = Standard power AP
-# 2 = Very low power AP (default)
-# 3 = Indoor enabled AP
-# 4 = Indoor standard power AP
+# 0 = Indoor AP (default)
+# 1 = Standard Power AP
 # This has no impact for operation on other bands.
-# See IEEE P802.11-REVme/D4.0, Table E-12 (Regulatory Info subfield encoding)
-# for more details.
 #he_6ghz_reg_pwr_type=0
-#
-# 6 GHz Maximum Tx Power used in Transmit Power Envelope elements, where the
-# "Transmit Power Interpretation" is set to "Regulatory client EIRP PSD".
-# For Maximum Transmit Power Category subfield encoding set to default (0):
-#reg_def_cli_eirp_psd=-1
-# For Maximum Transmit Power Category subfield encoding set to subordinate (1):
-#reg_sub_cli_eirp_psd=-1
 
 # Unsolicited broadcast Probe Response transmission settings
 # This is for the 6 GHz band only. If the interval is set to a non-zero value,
@@ -1039,20 +1027,6 @@
 #eht_oper_chwidth (see vht_oper_chwidth)
 #eht_oper_centr_freq_seg0_idx
 
-#eht_default_pe_duration: The duration of PE field in EHT TB PPDU
-# 0 = PE field duration is the same as he_default_pe_duration (default)
-# 1 = PE field duration is 20 us
-#eht_default_pe_duration=0
-
-#eht_bw320_offset: For automatic channel selection (ACS) to indicate a preferred
-# 320 MHz channelization in EHT mode.
-# If the channel is decided or the bandwidth is not 320 MHz, this option is
-# meaningless.
-# 0 = auto-detect by hostapd
-# 1 = 320 MHz-1 (channel center frequency 31, 95, 159)
-# 2 = 320 MHz-2 (channel center frequency 63, 127, 191)
-#eht_bw320_offset=0
-
 # Disabled subchannel bitmap (16 bits) as per IEEE P802.11be/3.0,
 # Figure 9-1002c (EHT Operation Information field format). Each bit corresponds
 # to a 20 MHz channel, the lowest bit corresponds to the lowest frequency. A
@@ -1801,10 +1775,6 @@
 #	Tunnel-Password
 # 3 = ask RADIUS server during 4-way handshake if there is no locally
 #	configured PSK/passphrase for the STA
-#
-# The Tunnel-Password attribute in Access-Accept can contain either the
-# 8..63 character ASCII passphrase or a 64 hex character encoding of the PSK.
-#
 #wpa_psk_radius=0
 
 # Set of accepted key management algorithms (WPA-PSK, WPA-EAP, or both). The
@@ -2062,10 +2032,6 @@
 #sae_password=really secret|mac=ff:ff:ff:ff:ff:ff
 #sae_password=example secret|mac=02:03:04:05:06:07|id=pw identifier
 #sae_password=example secret|vlanid=3|id=pw identifier
-#
-# SAE passwords can also be read from a separate file in which each line
-# contains and entry in the same format as sae_password uses.
-#sae_password_file=/tc/hostapd.sae_passwords
 
 # SAE threshold for anti-clogging mechanism (dot11RSNASAEAntiCloggingThreshold)
 # This parameter defines how many open SAE instances can be in progress at the
@@ -2295,12 +2261,6 @@
 # list and thus will receive push notifications.
 #r1kh=00:00:00:00:00:00 00:00:00:00:00:00 00112233445566778899aabbccddeeff
 
-# Optionally, the list of RxKHs can be read from a text file. Format is the same
-# as specified above. File shall contain both r0kh and r1kh. Once this variable
-# is set, RxKHs can be reloaded at runtime without bringing down an interface
-# using the RELOAD_RXKHS command.
-#rxkh_file=<path>
-
 # Timeout (seconds) for newly discovered R0KH/R1KH (see wildcard entries above)
 # Special values: 0 -> do not expire
 # Warning: do not cache implies no sequence number validation with wildcards