Cumulative patch from commit 05e5e615e6a26d7a9f5bd0569a0baeae1bcdee49
05e5e615e AP: Skip authentication/deauthentication phase for DMG/IEEE 802.11ad
0c4b9025c AP: Do not look for supported rates in DMG/IEEE 802.11ad
e72faadb4 bgscan_simple: Fix short_scan_count comparison
517b5f928 nl80211: Zero num_modes if nl80211_get_hw_feature_data() fails
39c5da328 nl80211: Use correct attribute for scan flags in vendor scan
c167662d7 eap_proxy: On SIM error flush PMKSAs only for SIM/AKA/AKA' networks
6657bb158 Fix OOM handling in neighbor report response handling
7187e2093 Allow LCI request with no subelements
d73420143 RRM: Enable beacon report with active/passive scan for all drivers
ec45927b8 Report received beacon report with BEACON-RESP-RX event
f3383366a Report beacon request TX status as control interface event
90d9d7c32 Beacon request through hostapd control interface
73a27a634 Add hostapd configuration parameter rrm_beacon_report
de6ec8b55 Enable Beacon Report using beacon table for all drivers
6774c6a9f Update copyright notices for the new year 2017
f56877414 Do not add own BSS in neighbor report with invalid op_class/channel
aeff0645d FILS: Fix FILS Realm Information ANQP-element construction
76196ddb2 wpa_supplicant: Add support for Beacon Report Radio Measurement
b3060bf99 common: Add helper function to convert RSSI to RCPI
1ac4dba31 wpa_supplicant: Extend verify_channel() and make it global
c9ff8e5f6 common: Add function to get an operating class by its number and country
e4f1d879c common: Add non-global to global operating classes conversion
96a5f14ee nl80211: Add support for additional scan parameters for beacon report
c16b9f8d3 driver: Add scan support to beacon report
3c716fdbd wpa_supplicant: Refactor wpas_rrm_build_lci_report()
e1b96e112 wpa_supplicant: Send rejection for unsupported radio measurements
0c73e410d wpa_supplicant: Limit RRM response size to MMPDU size
9664ab8b7 wpa_supplicant: Refactor Radio Measurement Request handling
332bf5d3f wpa_supplicant: Validate RRM request frame format
ec493469f wpa_supplicant: Move RRM implementation to a dedicated file
d1c74f8c9 Add RRM definitions for beacon report measurement
6a31440b8 Fix LCI request subelement processing
ce691a8d9 Add CONFIG_MESH into wpa_supplicant defconfig
67129ab9e wpa_cli: Add commands to use PMKSA_GET/ADD
bbad185c1 P2P: Fix compilation warning in p2p_add_device()
2977f5193 GAS: Remove unnecessarily duplicate gas_frag_limit configuration
1940559ea FT: Drop FT Action frames if ft_over_ds=0
d8de90487 Remove deprecated tx_queue_* params from hostapd.conf notes
78022c836 Fix memory leak on hostapd eap_user_file parsing error paths
02f999c6d hostapd: Remove unnecessary NULL check from parser functions
fd5f29e7e Fix memory leak in hostapd BSS_TM_REQ error path handling
95de34a10 Remove trailing whitespace
45997cce4 hostapd: Add TERMINATE as per-interface command
546680f81 hostapd: Do not update dtim_period with invalid value
356773058 RADIUS server: Increase maximum number of sessions
a5861afcb hostapd: Do not update invalid wep_key_len_unicast
f78402ace hostapd: Do not update rejected wep_key_len_broadcast
e0ba7efe5 hostapd: Do not update eapol_version with rejected value
9266d00bf hostapd: Reject invalid macaddr_acl value
8628555f9 hostapd: Check driver parameter before replacing previous value
1dfd25a68 Fix hostapd SIGHUP processing before interface is enabled
34e29dfd4 Remove unnecessary NULL check from hostapd_config_read_wpa_psk() call
65dfa8728 mka: Make MKA actor priority configurable
9bcfd5be8 Document new D-Bus WPS properties
77fcbf7ff D-Bus: Use a helper function to get possibly NULL strings
dbf524946 D-Bus: Add DeviceType in WPS property
266097fda D-Bus: Add device serial number in WPS property
3ee6a3ab3 D-Bus: Add model number in WPS property
ae66822cd D-Bus: Add WPS model name as property
318d4b5be D-Bus: Add WPS manufacturer as property
b20f031c6 D-Bus: Add WPS device name as property
4a45dc192 mesh: Show [MESH] flag in print_bss_info()
c04a67deb hostapd_cli: Add completion for get command
bf4167b9d hostapd_cli: Add completion for set command
86adff09e hostapd_cli: Completion for further commands with STA parameter
4f59ad069 hostapd_cli: Use common completion for commands that use stations
62b95eb67 hostapd_cli: Add missing command help descriptions
04f02faac Fix wpa_cipher_to_alg() return type
9187b13ad wpa_supplicant: Add BSS CURRENT control interface command
d7f12e4eb OpenSSL: Make sure local certificate auto chaining is enabled
4be02b71b OpenSSL: Remove SSL_{CTX_,}_clear_options ifdefs
7655bd738 P2P: Do not use wait_time for SD Response TX without fragmentation
1f0fdaf0e Fix race condition between AssocResp callback and 4addr event
a6f3761f7 eap_proxy: Add support for SIM state change indication from eap_proxy
79a54ab9f eap_proxy: Fix eap_proxy_init() prototype to use const eapol_cb
4e118c847 D-Bus: Add 'freq' option to P2P Find method to specify starting channel
e414f4f02 PeerKey: Fix STK 4-way handshake regression
28fb9bb19 PeerKey: Fix EAPOL-Key processing
dfc773172 Android: Add p2p_add_cli_chan=1 option
7508c2ad9 PAE: Make KaY specific details available via control interface
b54f43390 FILS: Make FILS Indication element information available in BSS output
8183aee6c FILS: Add support for building FILS Realm Information ANQP-element
9cad61867 FILS: Add Realm Information ANQP-element in BSS data
26bf70e3d FILS: Separate FILS realm configuration from ERP domain
42b847ac1 FILS: Fix hashed realm name derivation
29062f293 Update various definitions based on IEEE Std 802.11-2016
aaa9c60bc Fix preauth_test build by updating add_pmkid/remove_pmkid callbacks
0babae87a Fix wpa_supplicant build error with IEEE8021X_EAPOL unset
19810d29b Make Beacon IEs available in wpa_supplicant BSS command
274e76f22 mesh: Fix channel configuration in pri/sec switch case
cebda0e3e Make debug print clearer for AP/mesh mode secondary channel issues
3459381dd External persistent storage for PMKSA cache entries
c57931273 Add PMKSA-CACHE-ADDED/REMOVED events to wpa_supplicant
655dc4a43 Send "TERMINATING" event from hostapd
5149a0f04 P2P: Set p2p_persistent_group=1 at the time of reading disabled=2
065c029a5 Remove MBO dependency from Supported Operating Classes element
62cd9d792 nl80211: Specify the BSSID in the QCA vendor scan
444930e5b Define an attribute to do a specific BSSID QCA vendor scan
cea761472 Add QCA vendor command definitions for IDs 61-73
cb0cc6efa Define QCA Beacon miss threshold attributes for 2.4 and 5 GHz bands
c313c8a5d Fix QCA vendor command values for SAR power limits
a5c723adc Interworking: Clear SCANNING state if no network selected
a1836de64 SME: Fix IBSS setup after shared key/FT/FILS association
f49c852b5 P2P: Fix a theoretical out of bounds read in wpas_p2p_select_go_freq()
944d48588 P2P: Fix a theoretical out of bounds read in wpas_p2p_setup_freqs()
0a6c9dc70 P2P: Send P2P-DEVICE-FOUND event on peer changing device name
9a431d493 WFD: Clear wfd_subelems when P2P peer stops sending them
6e374bd44 Ignore scan results from ongoing scan when FLUSH command is issued
71ac93453 Make update_idx available in BSS control interface command
49aa88bb5 P2P: Clear PEER_WAITING_RESPONSE on GO Negotiation success
c79238b6a Define a QCA vendor command to configure SAR Power limits
0f5eb69f8 Use eloop timeout for post-EAP-Failure wait before disconnection
20b1a9e23 Allow hostapd wep_key# parameters to be cleared
5ec3d510e wpa_passphrase: Reject invalid passphrase
Test: Wifi Suite
Change-Id: Ida52ca4e43bbc326a89d4c9848529df2d545b692
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
diff --git a/src/common/qca-vendor.h b/src/common/qca-vendor.h
index 2ce2a89..46fddff 100644
--- a/src/common/qca-vendor.h
+++ b/src/common/qca-vendor.h
@@ -237,6 +237,12 @@
* started with QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN. This command
* carries the scan cookie of the corresponding scan request. The scan
* cookie is represented by QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS: Set the Specific
+ * Absorption Rate (SAR) power limits. A critical regulation for
+ * FCC compliance, OEMs require methods to set SAR limits on TX
+ * power of WLAN/WWAN. enum qca_vendor_attr_sar_limits
+ * attributes are used with this command.
*/
enum qca_nl80211_vendor_subcmds {
QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0,
@@ -288,7 +294,19 @@
QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED = 58,
QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED = 59,
QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED = 60,
- /* 61-73 - reserved for QCA */
+ QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO = 61,
+ QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START = 62,
+ QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_MEMORY_DUMP = 63,
+ QCA_NL80211_VENDOR_SUBCMD_ROAM = 64,
+ QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST = 65,
+ QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SSID_HOTLIST = 66,
+ QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_FOUND = 67,
+ QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_LOST = 68,
+ QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST = 69,
+ QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST = 70,
+ QCA_NL80211_VENDOR_SUBCMD_PNO_RESET_PASSPOINT_LIST = 71,
+ QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND = 72,
+ QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND = 73,
/* Wi-Fi configuration subcommands */
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION = 74,
QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION = 75,
@@ -345,6 +363,7 @@
QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS = 143,
/* 144 - reserved for QCA */
QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN = 145,
+ QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS = 146,
};
@@ -802,19 +821,22 @@
* scan flag is set
* @QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK: 6-byte MAC address mask to be used with
* randomisation
+ * @QCA_WLAN_VENDOR_ATTR_SCAN_BSSID: 6-byte MAC address representing the
+ * specific BSSID to scan for.
*/
enum qca_wlan_vendor_attr_scan {
QCA_WLAN_VENDOR_ATTR_SCAN_INVALID_PARAM = 0,
- QCA_WLAN_VENDOR_ATTR_SCAN_IE,
- QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES,
- QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS,
- QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES,
- QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE,
- QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS,
- QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE,
- QCA_WLAN_VENDOR_ATTR_SCAN_STATUS,
- QCA_WLAN_VENDOR_ATTR_SCAN_MAC,
- QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK,
+ QCA_WLAN_VENDOR_ATTR_SCAN_IE = 1,
+ QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES = 2,
+ QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS = 3,
+ QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES = 4,
+ QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE = 5,
+ QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS = 6,
+ QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE = 7,
+ QCA_WLAN_VENDOR_ATTR_SCAN_STATUS = 8,
+ QCA_WLAN_VENDOR_ATTR_SCAN_MAC = 9,
+ QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK = 10,
+ QCA_WLAN_VENDOR_ATTR_SCAN_BSSID = 11,
QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SCAN_MAX =
QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST - 1
@@ -1012,6 +1034,10 @@
QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_PEER_MAC = 35,
/* 32-bit unsigned value to set window size for specific peer */
QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_WINLIMIT = 36,
+ /* 8-bit unsigned value to set the beacon miss threshold in 2.4 GHz */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_24 = 37,
+ /* 8-bit unsigned value to set the beacon miss threshold in 5 GHz */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_5 = 38,
/* keep last */
QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST,
@@ -2214,4 +2240,676 @@
QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL = 1 << 2,
};
+/**
+ * enum qca_vendor_attr_sar_limits_selections - Source of SAR power limits
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0: Select SAR profile #0
+ * that is hard-coded in the Board Data File (BDF).
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1: Select SAR profile #1
+ * that is hard-coded in the Board Data File (BDF).
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2: Select SAR profile #2
+ * that is hard-coded in the Board Data File (BDF).
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3: Select SAR profile #3
+ * that is hard-coded in the Board Data File (BDF).
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4: Select SAR profile #4
+ * that is hard-coded in the Board Data File (BDF).
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE: Do not select any
+ * source of SAR power limits, thereby disabling the SAR power
+ * limit feature.
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER: Select the SAR power
+ * limits configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR.
+ *
+ * This enumerates the valid set of values that may be supplied for
+ * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT in an instance of
+ * the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor command.
+ */
+enum qca_vendor_attr_sar_limits_selections {
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0 = 0,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1 = 1,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2 = 2,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3 = 3,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4 = 4,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE = 5,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER = 6,
+};
+
+/**
+ * enum qca_vendor_attr_sar_limits_spec_modulations -
+ * SAR limits specification modulation
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK -
+ * CCK modulation
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM -
+ * OFDM modulation
+ *
+ * This enumerates the valid set of values that may be supplied for
+ * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION in an
+ * instance of attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC in an
+ * instance of the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor
+ * command.
+ */
+enum qca_vendor_attr_sar_limits_spec_modulations {
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK = 0,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM = 1,
+};
+
+/**
+ * enum qca_vendor_attr_sar_limits - Attributes for SAR power limits
+ *
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT: Optional (u32) value to
+ * select which SAR power limit table should be used. Valid
+ * values are enumerated in enum
+ * %qca_vendor_attr_sar_limits_selections. The existing SAR
+ * power limit selection is unchanged if this attribute is not
+ * present.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS: Optional (u32) value
+ * which specifies the number of SAR power limit specifications
+ * which will follow.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC: Nested array of SAR power
+ * limit specifications. The number of specifications is
+ * specified by @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS. Each
+ * specification contains a set of
+ * QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_* attributes. A
+ * specification is uniquely identified by the attributes
+ * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND,
+ * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN, and
+ * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION and always
+ * contains as a payload the attribute
+ * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND: Optional (u32) value to
+ * indicate for which band this specification applies. Valid
+ * values are enumerated in enum %nl80211_band (although not all
+ * bands may be supported by a given device). If the attribute is
+ * not supplied then the specification will be applied to all
+ * supported bands.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN: Optional (u32) value
+ * to indicate for which antenna chain this specification
+ * applies, i.e. 1 for chain 1, 2 for chain 2, etc. If the
+ * attribute is not supplied then the specification will be
+ * applied to all chains.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION: Optional (u32)
+ * value to indicate for which modulation scheme this
+ * specification applies. Valid values are enumerated in enum
+ * %qca_vendor_attr_sar_limits_spec_modulations. If the attribute
+ * is not supplied then the specification will be applied to all
+ * modulation schemes.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT: Required (u32)
+ * value to specify the actual power limit value in units of 0.5
+ * dBm (i.e., a value of 11 represents 5.5 dBm).
+ *
+ * These attributes are used with %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS.
+ */
+enum qca_vendor_attr_sar_limits {
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE = 1,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS = 2,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC = 3,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND = 4,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN = 5,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION = 6,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT = 7,
+
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_MAX =
+ QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST - 1
+};
+
+/**
+ * enum qca_wlan_vendor_attr_get_wifi_info: Attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO sub command.
+ */
+enum qca_wlan_vendor_attr_get_wifi_info {
+ QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION = 1,
+ QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION = 2,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_MAX =
+ QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST - 1,
+};
+
+/*
+ * enum qca_wlan_vendor_attr_wifi_logger_start: Attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START sub command.
+ */
+enum qca_wlan_vendor_attr_wifi_logger_start {
+ QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID = 1,
+ QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_VERBOSE_LEVEL = 2,
+ QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_FLAGS = 3,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_GET_MAX =
+ QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST - 1,
+};
+
+enum qca_wlan_vendor_attr_logger_results {
+ QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_INVALID = 0,
+
+ /* Unsigned 32-bit value; must match the request Id supplied by
+ * Wi-Fi HAL in the corresponding subcmd NL msg.
+ */
+ QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_REQUEST_ID = 1,
+
+ /* Unsigned 32-bit value; used to indicate the size of memory
+ * dump to be allocated.
+ */
+ QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MEMDUMP_SIZE = 2,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MAX =
+ QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST - 1,
+};
+
+enum qca_wlan_vendor_attr_roaming_config_params {
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_INVALID = 0,
+
+ QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD = 1,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_REQ_ID = 2,
+
+ /* Attributes for wifi_set_ssid_white_list */
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS = 3,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST = 4,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID = 5,
+
+ /* Attributes for set_roam_params */
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_THRESHOLD = 6,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_THRESHOLD = 7,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_FACTOR = 8,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_FACTOR = 9,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_MAX_BOOST = 10,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_LAZY_ROAM_HISTERESYS = 11,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALERT_ROAM_RSSI_TRIGGER = 12,
+
+ /* Attribute for set_lazy_roam */
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE = 13,
+
+ /* Attribute for set_lazy_roam with preferences */
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS = 14,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_NUM_BSSID = 15,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID = 16,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER = 17,
+
+ /* Attribute for set_blacklist bssid params */
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS = 18,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID = 19,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID = 20,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_MAX =
+ QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST - 1,
+};
+
+/*
+ * enum qca_wlan_vendor_attr_roam_subcmd: Attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_ROAM sub command.
+ */
+enum qca_wlan_vendor_attr_roam_subcmd {
+ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SSID_WHITE_LIST = 1,
+ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_GSCAN_ROAM_PARAMS = 2,
+ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_LAZY_ROAM = 3,
+ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PREFS = 4,
+ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PARAMS = 5,
+ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BLACKLIST_BSSID = 6,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_MAX =
+ QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST - 1,
+};
+
+enum qca_wlan_vendor_attr_gscan_config_params {
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_INVALID = 0,
+
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_REQUEST_ID = 1,
+
+ /* Attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS sub command.
+ */
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_WIFI_BAND
+ = 2,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_MAX_CHANNELS
+ = 3,
+
+ /* Attributes for input params used by
+ * QCA_NL80211_VENDOR_SUBCMD_GSCAN_START sub command.
+ */
+
+ /* Unsigned 32-bit value; channel frequency */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CHANNEL = 4,
+ /* Unsigned 32-bit value; dwell time in ms. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_DWELL_TIME = 5,
+ /* Unsigned 8-bit value; 0: active; 1: passive; N/A for DFS */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_PASSIVE = 6,
+ /* Unsigned 8-bit value; channel class */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CLASS = 7,
+
+ /* Unsigned 8-bit value; bucket index, 0 based */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_INDEX = 8,
+ /* Unsigned 8-bit value; band. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BAND = 9,
+ /* Unsigned 32-bit value; desired period, in ms. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_PERIOD = 10,
+ /* Unsigned 8-bit value; report events semantics. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_REPORT_EVENTS = 11,
+ /* Unsigned 32-bit value. Followed by a nested array of
+ * GSCAN_CHANNEL_SPEC_* attributes.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS = 12,
+
+ /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_* attributes.
+ * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC = 13,
+
+ /* Unsigned 32-bit value; base timer period in ms. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_BASE_PERIOD = 14,
+ /* Unsigned 32-bit value; number of APs to store in each scan in the
+ * BSSID/RSSI history buffer (keep the highest RSSI APs).
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_MAX_AP_PER_SCAN = 15,
+ /* Unsigned 8-bit value; in %, when scan buffer is this much full, wake
+ * up AP.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_PERCENT
+ = 16,
+
+ /* Unsigned 8-bit value; number of scan bucket specs; followed by a
+ * nested array of_GSCAN_BUCKET_SPEC_* attributes and values. The size
+ * of the array is determined by NUM_BUCKETS.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS = 17,
+
+ /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_* attributes.
+ * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC = 18,
+
+ /* Unsigned 8-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_FLUSH
+ = 19,
+ /* Unsigned 32-bit value; maximum number of results to be returned. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_MAX
+ = 20,
+
+ /* An array of 6 x unsigned 8-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_BSSID = 21,
+ /* Signed 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_LOW = 22,
+ /* Signed 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_HIGH = 23,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_CHANNEL = 24,
+
+ /* Number of hotlist APs as unsigned 32-bit value, followed by a nested
+ * array of AP_THRESHOLD_PARAM attributes and values. The size of the
+ * array is determined by NUM_AP.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_NUM_AP = 25,
+
+ /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_* attributes.
+ * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM = 26,
+
+ /* Unsigned 32-bit value; number of samples for averaging RSSI. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_RSSI_SAMPLE_SIZE
+ = 27,
+ /* Unsigned 32-bit value; number of samples to confirm AP loss. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_LOST_AP_SAMPLE_SIZE
+ = 28,
+ /* Unsigned 32-bit value; number of APs breaching threshold. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_MIN_BREACHING = 29,
+ /* Unsigned 32-bit value; number of APs. Followed by an array of
+ * AP_THRESHOLD_PARAM attributes. Size of the array is NUM_AP.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_NUM_AP = 30,
+ /* Unsigned 32-bit value; number of samples to confirm AP loss. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_LOST_AP_SAMPLE_SIZE
+ = 31,
+ /* Unsigned 32-bit value. If max_period is non zero or different than
+ * period, then this bucket is an exponential backoff bucket.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_MAX_PERIOD = 32,
+ /* Unsigned 32-bit value. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BASE = 33,
+ /* Unsigned 32-bit value. For exponential back off bucket, number of
+ * scans to perform for a given period.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_STEP_COUNT = 34,
+ /* Unsigned 8-bit value; in number of scans, wake up AP after these
+ * many scans.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_NUM_SCANS
+ = 35,
+
+ /* Attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST sub command.
+ */
+ /* Unsigned 3-2bit value; number of samples to confirm SSID loss. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_LOST_SSID_SAMPLE_SIZE
+ = 36,
+ /* Number of hotlist SSIDs as unsigned 32-bit value, followed by a
+ * nested array of SSID_THRESHOLD_PARAM_* attributes and values. The
+ * size of the array is determined by NUM_SSID.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID = 37,
+ /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_*
+ * attributes.
+ * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM = 38,
+
+ /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_SSID = 39,
+ /* Unsigned 8-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_BAND = 40,
+ /* Signed 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_LOW = 41,
+ /* Signed 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_HIGH = 42,
+ /* Unsigned 32-bit value; a bitmask with additional gscan config flag.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_CONFIGURATION_FLAGS = 43,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_MAX =
+ QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST - 1,
+};
+
+enum qca_wlan_vendor_attr_gscan_results {
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_INVALID = 0,
+
+ /* Unsigned 32-bit value; must match the request Id supplied by
+ * Wi-Fi HAL in the corresponding subcmd NL msg.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_REQUEST_ID = 1,
+
+ /* Unsigned 32-bit value; used to indicate the status response from
+ * firmware/driver for the vendor sub-command.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_STATUS = 2,
+
+ /* GSCAN Valid Channels attributes */
+ /* Unsigned 32bit value; followed by a nested array of CHANNELS. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_CHANNELS = 3,
+ /* An array of NUM_CHANNELS x unsigned 32-bit value integers
+ * representing channel numbers.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CHANNELS = 4,
+
+ /* GSCAN Capabilities attributes */
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_CACHE_SIZE = 5,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_BUCKETS = 6,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_AP_CACHE_PER_SCAN
+ = 7,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_RSSI_SAMPLE_SIZE
+ = 8,
+ /* Signed 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_REPORTING_THRESHOLD
+ = 9,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_BSSIDS = 10,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SIGNIFICANT_WIFI_CHANGE_APS
+ = 11,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_BSSID_HISTORY_ENTRIES
+ = 12,
+
+ /* GSCAN Attributes used with
+ * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE sub-command.
+ */
+
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE = 13,
+
+ /* GSCAN attributes used with
+ * QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT sub-command.
+ */
+
+ /* An array of NUM_RESULTS_AVAILABLE x
+ * QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_*
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST = 14,
+
+ /* Unsigned 64-bit value; age of sample at the time of retrieval */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_TIME_STAMP = 15,
+ /* 33 x unsigned 8-bit value; NULL terminated SSID */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_SSID = 16,
+ /* An array of 6 x unsigned 8-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BSSID = 17,
+ /* Unsigned 32-bit value; channel frequency in MHz */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CHANNEL = 18,
+ /* Signed 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RSSI = 19,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT = 20,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT_SD = 21,
+ /* Unsigned 16-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BEACON_PERIOD = 22,
+ /* Unsigned 16-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CAPABILITY = 23,
+ /* Unsigned 32-bit value; size of the IE DATA blob */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_LENGTH = 24,
+ /* An array of IE_LENGTH x unsigned 8-bit value; blob of all the
+ * information elements found in the beacon; this data should be a
+ * packed list of wifi_information_element objects, one after the
+ * other.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_DATA = 25,
+
+ /* Unsigned 8-bit value; set by driver to indicate more scan results are
+ * available.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_MORE_DATA = 26,
+
+ /* GSCAN attributes for
+ * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT sub-command.
+ */
+ /* Unsigned 8-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_TYPE = 27,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_STATUS = 28,
+
+ /* GSCAN attributes for
+ * QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND sub-command.
+ */
+ /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE
+ * to indicate number of results.
+ * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the
+ * list of results.
+ */
+
+ /* GSCAN attributes for
+ * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE sub-command.
+ */
+ /* An array of 6 x unsigned 8-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_BSSID = 29,
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_CHANNEL
+ = 30,
+ /* Unsigned 32-bit value. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_NUM_RSSI
+ = 31,
+ /* A nested array of signed 32-bit RSSI values. Size of the array is
+ * determined by (NUM_RSSI of SIGNIFICANT_CHANGE_RESULT_NUM_RSSI.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_RSSI_LIST
+ = 32,
+
+ /* GSCAN attributes used with
+ * QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS sub-command.
+ */
+ /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE
+ * to indicate number of gscan cached results returned.
+ * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST to indicate
+ * the list of gscan cached results.
+ */
+
+ /* An array of NUM_RESULTS_AVAILABLE x
+ * QCA_NL80211_VENDOR_ATTR_GSCAN_CACHED_RESULTS_*
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST = 33,
+ /* Unsigned 32-bit value; a unique identifier for the scan unit. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_SCAN_ID = 34,
+ /* Unsigned 32-bit value; a bitmask w/additional information about scan.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_FLAGS = 35,
+ /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE
+ * to indicate number of wifi scan results/bssids retrieved by the scan.
+ * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the
+ * list of wifi scan results returned for each cached result block.
+ */
+
+ /* GSCAN attributes for
+ * QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND sub-command.
+ */
+ /* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE for
+ * number of results.
+ * Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested
+ * list of wifi scan results returned for each
+ * wifi_passpoint_match_result block.
+ * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE.
+ */
+
+ /* GSCAN attributes for
+ * QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND sub-command.
+ */
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES
+ = 36,
+ /* A nested array of
+ * QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_*
+ * attributes. Array size =
+ * *_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_RESULT_LIST = 37,
+
+ /* Unsigned 32-bit value; network block id for the matched network */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ID = 38,
+ /* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested
+ * list of wifi scan results returned for each
+ * wifi_passpoint_match_result block.
+ */
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP_LEN = 39,
+ /* An array size of PASSPOINT_MATCH_ANQP_LEN of unsigned 8-bit values;
+ * ANQP data in the information_element format.
+ */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP = 40,
+
+ /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_SSIDS = 41,
+ /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS = 42,
+ /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS_BY_SSID
+ = 43,
+ /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_WHITELISTED_SSID
+ = 44,
+
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_BUCKETS_SCANNED = 45,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_MAX =
+ QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST - 1,
+};
+
+enum qca_wlan_vendor_attr_pno_config_params {
+ QCA_WLAN_VENDOR_ATTR_PNO_INVALID = 0,
+ /* Attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST sub command.
+ */
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM = 1,
+ /* Array of nested QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_*
+ * attributes. Array size =
+ * QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM.
+ */
+ QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NETWORK_ARRAY = 2,
+
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ID = 3,
+ /* An array of 256 x unsigned 8-bit value; NULL terminated UTF-8 encoded
+ * realm, 0 if unspecified.
+ */
+ QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_REALM = 4,
+ /* An array of 16 x unsigned 32-bit value; roaming consortium ids to
+ * match, 0 if unspecified.
+ */
+ QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_CNSRTM_ID = 5,
+ /* An array of 6 x unsigned 8-bit value; MCC/MNC combination, 0s if
+ * unspecified.
+ */
+ QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_PLMN = 6,
+
+ /* Attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST sub command.
+ */
+ /* Unsigned 32-bit value */
+ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS = 7,
+ /* Array of nested
+ * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_*
+ * attributes. Array size =
+ * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS.
+ */
+ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORKS_LIST = 8,
+ /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */
+ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_SSID = 9,
+ /* Signed 8-bit value; threshold for considering this SSID as found,
+ * required granularity for this threshold is 4 dBm to 8 dBm.
+ */
+ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_RSSI_THRESHOLD
+ = 10,
+ /* Unsigned 8-bit value; WIFI_PNO_FLAG_XXX */
+ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_FLAGS = 11,
+ /* Unsigned 8-bit value; auth bit field for matching WPA IE */
+ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_AUTH_BIT = 12,
+ /* Unsigned 8-bit to indicate ePNO type;
+ * It takes values from qca_wlan_epno_type
+ */
+ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_TYPE = 13,
+
+ /* Nested attribute to send the channel list */
+ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_CHANNEL_LIST = 14,
+
+ /* Unsigned 32-bit value; indicates the interval between PNO scan
+ * cycles in msec.
+ */
+ QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_SCAN_INTERVAL = 15,
+ QCA_WLAN_VENDOR_ATTR_EPNO_MIN5GHZ_RSSI = 16,
+ QCA_WLAN_VENDOR_ATTR_EPNO_MIN24GHZ_RSSI = 17,
+ QCA_WLAN_VENDOR_ATTR_EPNO_INITIAL_SCORE_MAX = 18,
+ QCA_WLAN_VENDOR_ATTR_EPNO_CURRENT_CONNECTION_BONUS = 19,
+ QCA_WLAN_VENDOR_ATTR_EPNO_SAME_NETWORK_BONUS = 20,
+ QCA_WLAN_VENDOR_ATTR_EPNO_SECURE_BONUS = 21,
+ QCA_WLAN_VENDOR_ATTR_EPNO_BAND5GHZ_BONUS = 22,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_PNO_MAX =
+ QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST - 1,
+};
+
#endif /* QCA_VENDOR_H */