Cumulative patch from commit ee48f48ba
The following commits are merged as well as changes in
./wpa_supplicant/hidl/1.3 to fix compilation errors.
ee48f48ba hostapd: Support showing neighbor list through hostapd_cli
3204795d7 STA OBSS: Add check for overlapping BSSs
3af78a4e0 Extract BSS coex 40 MHz check into a separate function
70755e658 Allow removing neighbor DB entries by BSSID alone
bf3ab50f4 Change some RRM debug messages from wpa_printf() to wpa_dbg()
a737e40b5 drivers: Support of dynamic VLAN requires Linux ioctls
9b391715c mesh: Allow group management cipher to be configured
65d0b67c2 mesh: Increase plink action frame AMPY buffer length for max GTK/IGTK
b1b62a136 WPS: Add WPS-PIN-ACTIVE and WPS-CANCEL events
0b1839405 Add "reconnect" cmdline argument to hostapd_cli/wpa_cli
4318a635a DBus: Update dont_quote[] with new network profile parameters
26a00ba8b DBus: Remove not existing network profile params from dont_quote[]
23d87687c dbus: Move roam metrics to the correct interface
8e111157e nl80211: Relax bridge setup
3626e72c8 l2_packet: Fix bridge workaround for repeater configuration
84972999b FT: More debug prints for RSNE modification for EAPOL-Key msg 2/4
4cfa8b92b Fix wpa_insert_pmkid() when buffer includes extra IEs
32289112c wpa_passphrase: Output errors to stderr
07fe134d9 EAP-SIM peer: Do not accept SIM/Challenge without SIM/Start
b2e2a8588 OpenSSL: Extend key_block size determination to support GCM/CCM ciphers
efaa6256e More detailed documentation on ieee80211w configuration parameter
1730a6a5e nl80211: Fix couple of typos in a comment
307cfc328 Strip trailing zero data in EAPOL-Key msg 1/4 when no PMKID to send
2c5ccfa60 nl80211: Initialize full channel info struct even if channel is not known
e6d3aca9c WPS: Add prefixes to public event_* functions
2ba6aa604 Fix memory leak in case allocation of token fails during JSON parsing
84877f253 wpa_supplicant: Do not try to detect PSK mismatch during PTK rekeying
78d338d1b DPP: Fix a memory leak on an error path
9be30ffc1 DPP: Abort ongoing scan if connection status needs to be sent
3f3876344 SAE: Enable NEED_DH_GROUPS_ALL for CONFIG_TESTING_OPTIONS=y builds
1f1567d2a QCA vendor command for getting STA information
e5620bf02 6 GHz: Select channel width using configured op_class
0bfc04b8d Do not enable HT/VHT when operating in 6 GHz band
da8570f4c Allow non-PCS 6 GHz channels to be excluded from ACS
59bb72642 Allow ACS channel list to be configured as frequencies (in MHz)
5f9b4afdf Use frequency in HT/VHT validation steps done before starting AP
59e33b4a9 ACS: Select current hw_mode based on the selected frequency
bb781c763 AP: Populate iface->freq before starting AP
41cac481a ACS: Use frequency params in ACS (offload) completed event interface
840532aea Search through all hw_features sets in hw_get_channel_freq()
15d356873 ACS: Add channels from all modes matching with configured hw mode
996662250 P2P: Add support for EDMG channels
f86e34168 Update operating classes and channels for the 60 GHz band
a19277a28 Add EDMG bandwidth to channel frequency APIs
5a563a3d3 Avoid compiler warning on shadowing a local variable
e3c476bd8 SAE H2E: Fix RSNXE override in EAPOL-Key msg 2/4 for testing purposes
7fde39fb1 Add sae_rejected_groups to hostapd STA control interface command
5661ebd77 DPP: Configurator netRole for Enrollee
740457445 DPP: Replace ap boolean with netRole enum in Configurator params
f2c4b44b4 SAE H2E: RSNXE override in EAPOL-Key msg 3/4
132565539 SAE H2E: RSNXE override for testing purposes
a889e9a70 SAE: Reject invalid rejected group report in SAE commit explicitly (AP)
c88e01e1b SAE H2E: Fix validation of rejected groups list
b834e9700 SAE H2E: Testing option to report extra rejected groups
918df2227 SAE: Reject unexpected Status Code in SAE commit explicitly (AP)
405946d76 SAE: Testing option to ignore H2E requirement mismatch
23acdd9f3 Fix memory leak in ACS offload operation
e86ba912a ACS: Remove redundant ch_list parameters from do_acs interface
3cf360b8e DFS: Don't handle DFS ops for 6 GHz channels
ee0030e81 6 GHz: Do not check for HT capability on 6 GHz channels
e780b4bf2 DPP: Bootstrapping via NFC URI Record
3c0d6eb8a Sync with mac80211-next.git include/uapi/linux/nl80211.h
38203148e Extend hostapd to support setband to driver via QCA vendor command
3c13af557 hostapd: Register wpa_msg callback even if only global ctrl_iface is used
e92080568 hostapd: Extend global control interface notifications
9f50538e1 SAE H2E: Do not use sae_h2e param in AP mode if SAE is disabled
181bf9336 DPP2: Report received ssid_charset as DPP-CONFOBJ-SSID-CHARSET event
71e2848ea DPP2: ssid64/ssid_charset in Configurator
57a63b131 DPP2: Add parsing of ssid64/ssid_charset in Config Object
590bc64d6 DPP: Use JSON token builder helpers
e75ab5322 JSON: Add helper functions for building tokens
8e5e36a18 Clean up base64_{encode,decode} pointer types
b22608423 Clean up base64_url_{encode,decode} pointer types
a4255a207 Simplify base64_url_encode() prototype
c54227c26 DPP2: Replace connectionStatus object ssid with ssid64
31b6eb417 tests: Update SAE H2E test case to match SSWU parameter z change
0432237a4 SAE H2E: Update SSWU curve-specific parameter z values
5b50265e1 WMM: Do not modify input TSPEC buffer during processing
783a99b73 HS2.0: Skip check for roaming_consortium for NAI realm query
f3c077929 P2P: Fix listen state machine getting stuck in send_action() scheduled case
530b8ee3c hostapd: Update DFS status in VHT80+80 mode
93ba13bcf Fix status code in SAE/DPP association PMKID mismatch (driver-AP-SME)
b90d2f7ff Fix a typo in a comment
Bug: 146900007
Test: Device boots up and connects to wifi networks, run traffic.
Test: Able to turn on/off softap, associate wifi STA, run traffic.
Test: Regression test Passed (Bug: 146905211)
Change-Id: Idc3584b491429a2e4935068a293bff572fc9d62e
diff --git a/src/common/qca-vendor.h b/src/common/qca-vendor.h
index a0a0fb5..778c217 100644
--- a/src/common/qca-vendor.h
+++ b/src/common/qca-vendor.h
@@ -609,6 +609,14 @@
* coex chain mode from application/service.
* The attributes defined in enum qca_vendor_attr_btc_chain_mode are used
* to deliver the parameters.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO: This vendor subcommand is used to
+ * get information of a station from driver to userspace. This command can
+ * be used in both STA and AP modes. For STA mode, it provides information
+ * of the current association when in connected state or the last
+ * association when in disconnected state. For AP mode, only information
+ * of the currently connected stations is available. This command uses
+ * attributes defined in enum qca_wlan_vendor_attr_get_sta_info.
*/
enum qca_nl80211_vendor_subcmds {
QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0,
@@ -784,6 +792,7 @@
QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT = 183,
QCA_NL80211_VENDOR_SUBCMD_ADD_STA_NODE = 184,
QCA_NL80211_VENDOR_SUBCMD_BTC_CHAIN_MODE = 185,
+ QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO = 186,
};
enum qca_wlan_vendor_attr {
@@ -8046,4 +8055,110 @@
QCA_VENDOR_ATTR_BTC_CHAIN_MODE_LAST - 1,
};
+/**
+ * enum qca_vendor_wlan_sta_flags - Station feature flags
+ * Bits will be set to 1 if the corresponding features are enabled.
+ * @QCA_VENDOR_WLAN_STA_FLAG_AMPDU: AMPDU is enabled for the station
+ * @QCA_VENDOR_WLAN_STA_FLAG_TX_STBC: TX Space-time block coding is enabled
+ for the station
+ * @QCA_VENDOR_WLAN_STA_FLAG_RX_STBC: RX Space-time block coding is enabled
+ for the station
+ */
+enum qca_vendor_wlan_sta_flags {
+ QCA_VENDOR_WLAN_STA_FLAG_AMPDU = BIT(0),
+ QCA_VENDOR_WLAN_STA_FLAG_TX_STBC = BIT(1),
+ QCA_VENDOR_WLAN_STA_FLAG_RX_STBC = BIT(2),
+};
+
+/**
+ * enum qca_vendor_wlan_sta_guard_interval - Station guard interval
+ * @QCA_VENDOR_WLAN_STA_GI_800_NS: Legacy normal guard interval
+ * @QCA_VENDOR_WLAN_STA_GI_400_NS: Legacy short guard interval
+ * @QCA_VENDOR_WLAN_STA_GI_1600_NS: Guard interval used by HE
+ * @QCA_VENDOR_WLAN_STA_GI_3200_NS: Guard interval used by HE
+ */
+enum qca_vendor_wlan_sta_guard_interval {
+ QCA_VENDOR_WLAN_STA_GI_800_NS = 0,
+ QCA_VENDOR_WLAN_STA_GI_400_NS = 1,
+ QCA_VENDOR_WLAN_STA_GI_1600_NS = 2,
+ QCA_VENDOR_WLAN_STA_GI_3200_NS = 3,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_get_sta_info - Defines attributes
+ * used by QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO vendor command.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAC:
+ * Required attribute in request, 6-byte MAC address,
+ * used in both STA and AP modes.
+ * MAC address of the station for which information is requested (BSSID of the
+ * AP in STA mode).
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_FLAGS:
+ * Optionally used in response, u32 attribute, contains a bitmap of different
+ * fields defined in enum qca_vendor_wlan_sta_flags, used in AP mode only.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_GUARD_INTERVAL:
+ * Optionally used in response, u32 attribute, possible values are defined in
+ * enum qca_vendor_wlan_sta_guard_interval, used in AP mode only.
+ * Guard interval used by the station.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_RETRY_COUNT:
+ * Optionally used in response, u32 attribute, used in AP mode only.
+ * Value indicates the number of data frames received from station with retry
+ * bit set to 1 in FC.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BC_MC_COUNT:
+ * Optionally used in response, u32 attribute, used in AP mode only.
+ * Counter for number of data frames with broadcast or multicast address in
+ * the destination address received from the station.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RETRY_SUCCEED:
+ * Optionally used in response, u32 attribute, used in both STA and AP modes.
+ * Value indicates the number of data frames successfully transmitted only
+ * after retrying the packets and for which the TX status has been updated
+ * back to host from target.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RETRY_EXHAUSTED:
+ * Optionally used in response, u32 attribute, used in AP mode only.
+ * Value indicates the number of data frames not transmitted successfully even
+ * after retrying the packets for the number of times equal to the total number
+ * of retries allowed for that packet and for which the TX status has been
+ * updated back to host from target.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_TOTAL:
+ * Optionally used in response, u32 attribute, used in AP mode only.
+ * Counter in the target for the number of data frames successfully transmitted
+ * to the station.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_RETRY:
+ * Optionally used in response, u32 attribute, used in AP mode only.
+ * Value indicates the number of data frames successfully transmitted only
+ * after retrying the packets.
+ *
+ * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_RETRY_EXHAUSTED:
+ * Optionally used in response, u32 attribute, used in AP mode only.
+ * Value indicates the number of data frames not transmitted successfully even
+ * after retrying the packets for the number of times equal to the total number
+ * of retries allowed for that packet.
+ */
+enum qca_wlan_vendor_attr_get_sta_info {
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAC = 1,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_FLAGS = 2,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_GUARD_INTERVAL = 3,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_RETRY_COUNT = 4,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BC_MC_COUNT = 5,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RETRY_SUCCEED = 6,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RETRY_EXHAUSTED = 7,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_TOTAL = 8,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_RETRY = 9,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_RETRY_EXHAUSTED = 10,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAX =
+ QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_AFTER_LAST - 1,
+};
+
#endif /* QCA_VENDOR_H */