Cumulative patch from commit a9491695b30a7f750dc45cb563d813b03f1d4b8d
a9491695b QCA vendor command to set/get NUD statistics
f593b6c11 nl80211: Do not reset vendor_scan_cookie after scan timeout
f2bc34480 wpa_supplicant: Fix global control interface for STA/STA-FIRST/STA-NEXT
cc3dae85b hostapd: Add possibility to send debug messages to syslog
0da355235 FST: Remove WPA_ASSERT from wpas_fst_send_action_cb()
968dce9b1 FST: Silence compiler warning on WPA_ASSERT
17e20b1e2 FST: Remove a bogus WPA_ASSERT()
6a5425fd6 Increase delayed EAPOL RX frame timeout
cef8fac04 wpa_auth: Make struct wpa_auth_callbacks const
30eddf352 Fix or supress various sparse warnings
b301f54e5 IBSS/mesh: Skip VHT channel setup with vht_disabled=1
adc6a5d81 mesh: Check remote peer HT Operation element
9eb5757a8 Define helper function set_disable_ht40()
7813b7c34 nl80211: Fix a memory leak on deinit with HT enabled mesh
6b585f420 mesh: Fix crash on removing virtual mesh interface
5208160b4 FILS: Parse received FILS HLP requests
5732b770f FILS: Allow FILS HLP requests to be added
a1aa2aebc Remove unused WLAN_CIPHER_SUITE_* definitions
a042e39ac nl80211: Use RSN_CIPHER_SUITE_* instead of WLAN_CIPHER_SUITE_*
2373a3117 Define all RSN_CIPHER_SUITE_* values
89ba101e1 Remove unused WLAN_AKM_SUITE_* definitions
bf9f8a052 Use RSN_AUTH_KEY_MGMT_* instead of WLAN_AKM_SUITE_* for wpa_akm_to_suite()
3aa24db95 nl80211: Use RSN_AUTH_KEY_MGMT_* instead of WLAN_AKM_SUITE_*
a1343fa6b Remove unnecessary ifdef from RSN_AUTH_KEY_MGMT_* definitions
afe731004 Fix CONFIG_SAE build without CONFIG_SME
34e8bfd7a Skip EVENT_ACS_CHANNEL_SELECTED also without CONFIG_AP
510fc2dfc Fix AKM suite selectors for FILS and Suite B
d7d0f909f QCA vendor command to carry the reason for power save failure
53b38209f GAS: Cancel gas_query_timeout when AP responds with comeback delay
d5bd94133 MBO: Silence a compiler warning when building without CONFIG_MBO
4c4070005 QCA vendor command to enable host driver offload ACS to user space
4d77d80ed mesh: Add MESH_PMKSA_GET/ADD commands
117875db3 D-Bus: Add GroupMgmt entry into the interface Capabilities dict
3cdb4ac07 D-Bus: Add pmf to global capabilities
adf8f45f8 D-Bus: Implement Pmf property
b98706c14 RSN IBSS: Fix TK clearing on Authentication frame RX
fa67debf4 Fix duplicate Reassociation Request frame dropping
6ff92677a wext: Cancel send_rfkill timeout in deinit
fcd3d6ce3 FILS: Fix PMK and PMKID derivation from ERP
ef495c78d OpenSSL: Implement sha384_vector()
a70cd0db8 nl80211: Don't register for Beacon frames for IEEE 802.11ad AP
a2aa21a3b Assign additional vendor specific elements for early HE testing
f09095d57 wpa_supplicant: Clarify group_rekey documentation
c85dfc6f8 nl80211: Set NL80211_ATTR_IFACE_SOCKET_OWNER for connect and associate
d07f450da Sync with mac80211-next.git include/uapi/linux/nl80211.h
8f315d050 Fix country code in wpa_supplicant AP mode Country element
29065686a D-Bus: Fix BSS Mode getter for invalid DMG BSS
b2442f256 nl80211: Debug prints for TDLS_OPER command and result
2901bc272 bgscan: Remove unnecessary NULL check
9d6eaad6b bgscan: Remove unnecessary NULL check
0f9b4a0f1 bgscan: Deliver beacon loss event to bgscan modules
688556722 nl80211: More complete processing of connection quality monitor events
54736d835 Store FST parameters to configuration file
35c78f7b9 Store osu_dir to configuration file
1f539c78f Store autoscan to configuration file
58ed9e31d Store filter_rssi to configuration file
1fb1bf99d Write sec_device_type to configuration file
b4bdeadfa Make "SET" behavior more consistent for dot11RSNA parameters
e3394c0e2 Make "SET non_pref_chan .." behavior more consistent
f8c201862 Fix cert_in_cb parsing in wpa_supplicant.conf
9284418d0 Fix writing of wpa_supplicant sae_groups configuration parameter
167f78a5e Send BEACON-REQ-TX-STATUS event only for beacon reports
7ba94fc4b RRM: Use wpa_hexdump_buf() instead of wpa_hexdump()
e4ec6bbfd nl80211: Register for Link Measurement Report frames in AP mode
33468e532 RRM: Document Link Measurement Report frame construction steps
40e9a3f32 RRM: Fix beacon report scan channels for VHT 80, 80+80, 160 MHz cases
5cda35089 RRM: Move wpabuf_resize() call into wpas_rrm_report_elem()
f2058f4af RRM: Remove unnecessary cb check
89fa633af nl80211: Fix error while enabling AP mode with driver-SME
The last change 89fa633af cherrypicks a later change that resolves
an issue with starting up AP mode.
Bug: 34681709
Test: Wifi Suite
Change-Id: Iba8c5824009d6480fb736b274d69243c77aef7fe
diff --git a/src/common/qca-vendor.h b/src/common/qca-vendor.h
index 46fddff..25800d4 100644
--- a/src/common/qca-vendor.h
+++ b/src/common/qca-vendor.h
@@ -243,6 +243,30 @@
* FCC compliance, OEMs require methods to set SAR limits on TX
* power of WLAN/WWAN. enum qca_vendor_attr_sar_limits
* attributes are used with this command.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS: This command/event is used by the
+ * host driver for offloading the implementation of Auto Channel Selection
+ * (ACS) to an external user space entity. This interface is used as the
+ * event from the host driver to the user space entity and also as the
+ * request from the user space entity to the host driver. The event from
+ * the host driver is used by the user space entity as an indication to
+ * start the ACS functionality. The attributes used by this event are
+ * represented by the enum qca_wlan_vendor_attr_external_acs_event.
+ * User space entity uses the same interface to inform the host driver with
+ * selected channels after the ACS operation using the attributes defined
+ * by enum qca_wlan_vendor_attr_external_acs_channels.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE: Vendor event carrying the
+ * requisite information leading to a power save failure. The information
+ * carried as part of this event is represented by the
+ * enum qca_attr_chip_power_save_failure attributes.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET: Start/Stop the NUD statistics
+ * collection. Uses attributes defined in enum qca_attr_nud_stats_set.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET: Get the NUD statistics. These
+ * statistics are represented by the enum qca_attr_nud_stats_get
+ * attributes.
*/
enum qca_nl80211_vendor_subcmds {
QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0,
@@ -364,6 +388,10 @@
/* 144 - reserved for QCA */
QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN = 145,
QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS = 146,
+ QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS = 147,
+ QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE = 148,
+ QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET = 149,
+ QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET = 150,
};
@@ -794,11 +822,39 @@
* vendor specific element is defined by the latest P802.11ax draft.
* Please note that the draft is still work in progress and this element
* payload is subject to change.
+ *
+ * @QCA_VENDOR_ELEM_RAPS: RAPS element (OFDMA-based Random Access Parameter Set
+ * element).
+ * This element can be used for pre-standard publication testing of HE
+ * before P802.11ax draft assigns the element ID extension. The payload of
+ * this vendor specific element is defined by the latest P802.11ax draft
+ * (not including the Element ID Extension field). Please note that the
+ * draft is still work in progress and this element payload is subject to
+ * change.
+ *
+ * @QCA_VENDOR_ELEM_MU_EDCA_PARAMS: MU EDCA Parameter Set element.
+ * This element can be used for pre-standard publication testing of HE
+ * before P802.11ax draft assigns the element ID extension. The payload of
+ * this vendor specific element is defined by the latest P802.11ax draft
+ * (not including the Element ID Extension field). Please note that the
+ * draft is still work in progress and this element payload is subject to
+ * change.
+ *
+ * @QCA_VENDOR_ELEM_BSS_COLOR_CHANGE: BSS Color Change Announcement element.
+ * This element can be used for pre-standard publication testing of HE
+ * before P802.11ax draft assigns the element ID extension. The payload of
+ * this vendor specific element is defined by the latest P802.11ax draft
+ * (not including the Element ID Extension field). Please note that the
+ * draft is still work in progress and this element payload is subject to
+ * change.
*/
enum qca_vendor_element_id {
QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST = 0,
QCA_VENDOR_ELEM_HE_CAPAB = 1,
QCA_VENDOR_ELEM_HE_OPER = 2,
+ QCA_VENDOR_ELEM_RAPS = 3,
+ QCA_VENDOR_ELEM_MU_EDCA_PARAMS = 4,
+ QCA_VENDOR_ELEM_BSS_COLOR_CHANGE = 5,
};
/**
@@ -2912,4 +2968,340 @@
QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST - 1,
};
+/**
+ * qca_wlan_vendor_acs_select_reason: This represents the different reasons why
+ * the ACS has to be triggered. These values are used by
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON and
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON
+ */
+enum qca_wlan_vendor_acs_select_reason {
+ /* Represents the reason that the ACS triggered during the AP start */
+ QCA_WLAN_VENDOR_ACS_SELECT_REASON_INIT,
+ /* Represents the reason that DFS found with the current channel */
+ QCA_WLAN_VENDOR_ACS_SELECT_REASON_DFS,
+ /* Represents the reason that LTE co-exist in the current band. */
+ QCA_WLAN_VENDOR_ACS_SELECT_REASON_LTE_COEX,
+};
+
+/**
+ * qca_wlan_vendor_channel_prop_flags: This represent the flags for a channel.
+ * This is used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS.
+ */
+enum qca_wlan_vendor_channel_prop_flags {
+ /* Bits 0, 1, 2, and 3 are reserved */
+
+ /* Turbo channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_TURBO = 1 << 4,
+ /* CCK channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_CCK = 1 << 5,
+ /* OFDM channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_OFDM = 1 << 6,
+ /* 2.4 GHz spectrum channel. */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_2GHZ = 1 << 7,
+ /* 5 GHz spectrum channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_5GHZ = 1 << 8,
+ /* Only passive scan allowed */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_PASSIVE = 1 << 9,
+ /* Dynamic CCK-OFDM channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_DYN = 1 << 10,
+ /* GFSK channel (FHSS PHY) */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_GFSK = 1 << 11,
+ /* Radar found on channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_RADAR = 1 << 12,
+ /* 11a static turbo channel only */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_STURBO = 1 << 13,
+ /* Half rate channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HALF = 1 << 14,
+ /* Quarter rate channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_QUARTER = 1 << 15,
+ /* HT 20 channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT20 = 1 << 16,
+ /* HT 40 with extension channel above */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40PLUS = 1 << 17,
+ /* HT 40 with extension channel below */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40MINUS = 1 << 18,
+ /* HT 40 intolerant */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOL = 1 << 19,
+ /* VHT 20 channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT20 = 1 << 20,
+ /* VHT 40 with extension channel above */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40PLUS = 1 << 21,
+ /* VHT 40 with extension channel below */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40MINUS = 1 << 22,
+ /* VHT 80 channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80 = 1 << 23,
+ /* HT 40 intolerant mark bit for ACS use */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOLMARK = 1 << 24,
+ /* Channel temporarily blocked due to noise */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_BLOCKED = 1 << 25,
+ /* VHT 160 channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT160 = 1 << 26,
+ /* VHT 80+80 channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80_80 = 1 << 27,
+};
+
+/**
+ * qca_wlan_vendor_channel_prop_flags_ext: This represent the extended flags for
+ * each channel. This is used by
+ * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT.
+ */
+enum qca_wlan_vendor_channel_prop_flags_ext {
+ /* Radar found on channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_RADAR_FOUND = 1 << 0,
+ /* DFS required on channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS = 1 << 1,
+ /* DFS required on channel for 2nd band of 80+80 */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CFREQ2 = 1 << 2,
+ /* If channel has been checked for DFS */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CLEAR = 1 << 3,
+ /* Excluded in 802.11d */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_11D_EXCLUDED = 1 << 4,
+ /* Channel Switch Announcement received on this channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CSA_RECEIVED = 1 << 5,
+ /* Ad-hoc is not allowed */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_ADHOC = 1 << 6,
+ /* Station only channel */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_HOSTAP = 1 << 7,
+ /* DFS radar history for slave device (STA mode) */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_HISTORY_RADAR = 1 << 8,
+ /* DFS CAC valid for slave device (STA mode) */
+ QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CAC_VALID = 1 << 9,
+};
+
+/**
+ * qca_wlan_vendor_external_acs_event_chan_info_attr: Represents per channel
+ * information. These attributes are sent as part of
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO. Each set of the following
+ * attributes correspond to a single channel.
+ */
+enum qca_wlan_vendor_external_acs_event_chan_info_attr {
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_INVALID = 0,
+
+ /* A bitmask (u32) with flags specified in
+ * enum qca_wlan_vendor_channel_prop_flags.
+ */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS = 1,
+ /* A bitmask (u32) with flags specified in
+ * enum qca_wlan_vendor_channel_prop_flags_ext.
+ */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT = 2,
+ /* frequency in MHz (u32) */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ = 3,
+ /* maximum regulatory transmission power (u32) */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_REG_POWER = 4,
+ /* maximum transmission power (u32) */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_POWER = 5,
+ /* minimum transmission power (u32) */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MIN_POWER = 6,
+ /* regulatory class id (u8) */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_REG_CLASS_ID = 7,
+ /* maximum antenna gain in (u8) */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_ANTENNA_GAIN = 8,
+ /* VHT segment 0 (u8) */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0 = 9,
+ /* VHT segment 1 (u8) */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1 = 10,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST,
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX =
+ QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST - 1,
+};
+
+/**
+ * qca_wlan_vendor_attr_pcl: Represents attributes for
+ * preferred channel list (PCL). These attributes are sent as part of
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL.
+ */
+enum qca_wlan_vendor_attr_pcl {
+ QCA_WLAN_VENDOR_ATTR_PCL_INVALID = 0,
+
+ /* Channel number (u8) */
+ QCA_WLAN_VENDOR_ATTR_PCL_CHANNEL = 1,
+ /* Channel weightage (u8) */
+ QCA_WLAN_VENDOR_ATTR_PCL_WEIGHT = 2,
+};
+
+/**
+ * qca_wlan_vendor_attr_external_acs_event: Attribute to vendor sub-command
+ * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This attribute will be sent by
+ * host driver.
+ */
+enum qca_wlan_vendor_attr_external_acs_event {
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_INVALID = 0,
+
+ /* This reason (u8) refers to enum qca_wlan_vendor_acs_select_reason.
+ * This helps ACS module to understand why ACS needs to be started.
+ */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON = 1,
+ /* Flag attribute to indicate if driver supports spectral scanning */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_SPECTRAL_SUPPORTED = 2,
+ /* Flag attribute to indicate if 11ac is offloaded to firmware */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_OFFLOAD_ENABLED = 3,
+ /* Flag attribute to indicate if driver provides additional channel
+ * capability as part of scan operation */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_ADD_CHAN_STATS_SUPPORT = 4,
+ /* Flag attribute to indicate interface status is UP */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_AP_UP = 5,
+ /* Operating mode (u8) of interface. Takes one of enum nl80211_iftype
+ * values. */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_SAP_MODE = 6,
+ /* Channel width (u8). It takes one of enum nl80211_chan_width values.
+ * This is the upper bound of channel width. ACS logic should try to get
+ * a channel with the specified width and if not found, look for lower
+ * values.
+ */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_WIDTH = 7,
+ /* This (u8) will hold values of one of enum nl80211_bands */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_BAND = 8,
+ /* PHY/HW mode (u8). Takes one of enum qca_wlan_vendor_acs_hw_mode
+ * values */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PHY_MODE = 9,
+ /* Array of (u32) supported frequency list among which ACS should choose
+ * best frequency.
+ */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_FREQ_LIST = 10,
+ /* Preferred channel list by the driver which will have array of nested
+ * values as per enum qca_wlan_vendor_attr_pcl attribute.
+ */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL = 11,
+ /* Array of nested attribute for each channel. It takes attr as defined
+ * in enum qca_wlan_vendor_external_acs_event_chan_info_attr.
+ */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO = 12,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST,
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_MAX =
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST - 1,
+};
+
+/**
+ * qca_wlan_vendor_attr_external_acs_channels: Attributes to vendor subcmd
+ * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This carries a list of channels
+ * in priority order as decided after ACS operation in userspace.
+ */
+enum qca_wlan_vendor_attr_external_acs_channels {
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_INVALID = 0,
+
+ /* One of reason code (u8) from enum qca_wlan_vendor_acs_select_reason
+ */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON = 1,
+
+ /* Array of nested values for each channel with following attributes:
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1,
+ * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH
+ */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST = 2,
+ /* This (u8) will hold values of one of enum nl80211_bands */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND = 3,
+ /* Primary channel (u8) */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY = 4,
+ /* Secondary channel (u8) used for HT 40 MHz channels */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY = 5,
+ /* VHT seg0 channel (u8) */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0 = 6,
+ /* VHT seg1 channel (u8) */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1 = 7,
+ /* Channel width (u8). Takes one of enum nl80211_chan_width values. */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH = 8,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST,
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_MAX =
+ QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST - 1
+};
+
+enum qca_chip_power_save_failure_reason {
+ /* Indicates if the reason for the failure is due to a protocol
+ * layer/module.
+ */
+ QCA_CHIP_POWER_SAVE_FAILURE_REASON_PROTOCOL = 0,
+ /* Indicates if the reason for the failure is due to a hardware issue.
+ */
+ QCA_CHIP_POWER_SAVE_FAILURE_REASON_HARDWARE = 1,
+};
+
+/**
+ * qca_attr_chip_power_save_failure: Attributes to vendor subcmd
+ * QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE. This carries the requisite
+ * information leading to the power save failure.
+ */
+enum qca_attr_chip_power_save_failure {
+ QCA_ATTR_CHIP_POWER_SAVE_FAILURE_INVALID = 0,
+ /* Reason to cause the power save failure.
+ * These reasons are represented by
+ * enum qca_chip_power_save_failure_reason.
+ */
+ QCA_ATTR_CHIP_POWER_SAVE_FAILURE_REASON = 1,
+
+ /* keep last */
+ QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST,
+ QCA_ATTR_CHIP_POWER_SAVE_FAILURE_MAX =
+ QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST - 1,
+};
+
+/**
+ * qca_wlan_vendor_attr_nud_stats_set: Attributes to vendor subcmd
+ * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carries the requisite
+ * information to start/stop the NUD statistics collection.
+ */
+enum qca_attr_nud_stats_set {
+ QCA_ATTR_NUD_STATS_SET_INVALID = 0,
+
+ /* Flag to start/stop the NUD statistics collection.
+ * Start - If included, Stop - If not included
+ */
+ QCA_ATTR_NUD_STATS_SET_START = 1,
+ /* IPv4 address of the default gateway (in network byte order) */
+ QCA_ATTR_NUD_STATS_GW_IPV4 = 2,
+
+ /* keep last */
+ QCA_ATTR_NUD_STATS_SET_LAST,
+ QCA_ATTR_NUD_STATS_SET_MAX =
+ QCA_ATTR_NUD_STATS_SET_LAST - 1,
+};
+
+/**
+ * qca_attr_nud_stats_get: Attributes to vendor subcmd
+ * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET. This carries the requisite
+ * NUD statistics collected when queried.
+ */
+enum qca_attr_nud_stats_get {
+ QCA_ATTR_NUD_STATS_GET_INVALID = 0,
+ /* ARP Request count from netdev */
+ QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_FROM_NETDEV = 1,
+ /* ARP Request count sent to lower MAC from upper MAC */
+ QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TO_LOWER_MAC = 2,
+ /* ARP Request count received by lower MAC from upper MAC */
+ QCA_ATTR_NUD_STATS_ARP_REQ_RX_COUNT_BY_LOWER_MAC = 3,
+ /* ARP Request count successfully transmitted by the device */
+ QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TX_SUCCESS = 4,
+ /* ARP Response count received by lower MAC */
+ QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_LOWER_MAC = 5,
+ /* ARP Response count received by upper MAC */
+ QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_UPPER_MAC = 6,
+ /* ARP Response count delivered to netdev */
+ QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_TO_NETDEV = 7,
+ /* ARP Response count delivered to netdev */
+ QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_OUT_OF_ORDER_DROP = 8,
+ /* Flag indicating if the station's link to the AP is active.
+ * Active Link - If included, Inactive link - If not included
+ */
+ QCA_ATTR_NUD_STATS_AP_LINK_ACTIVE= 9,
+ /* Flag indicating if there is any duplicate address detected (DAD).
+ * Yes - If detected, No - If not detected.
+ */
+ QCA_ATTR_NUD_STATS_IS_DAD = 9,
+
+ /* keep last */
+ QCA_ATTR_NUD_STATS_GET_LAST,
+ QCA_ATTR_NUD_STATS_GET_MAX =
+ QCA_ATTR_NUD_STATS_GET_LAST - 1,
+};
+
#endif /* QCA_VENDOR_H */