runtime(doc): format jumplist examples more consistently (#13137)
Signed-off-by: Christian Brabandt <cb@256bit.org>
diff --git a/runtime/doc/motion.txt b/runtime/doc/motion.txt
index 9bdbfb4..73fc9a8 100644
--- a/runtime/doc/motion.txt
+++ b/runtime/doc/motion.txt
@@ -1071,14 +1071,14 @@
move up and down the list. There is a separate jump list for each window.
The maximum number of entries is fixed at 100.
-For example, after three jump commands you have this jump list:
+For example, after three jump commands you have this jump list: >
- jump line col file/text ~
- 3 1 0 some text ~
- 2 70 0 another line ~
- 1 1154 23 end. ~
- > ~
-
+ jump line col file/text
+ 3 1 0 some text
+ 2 70 0 another line
+ 1 1154 23 end.
+ >
+<
The "file/text" column shows the file name, or the text at the jump if it is
in the current file (an indent is removed and a long line is truncated to fit
in the window).
@@ -1087,14 +1087,14 @@
shown when filtering the |:jumps| command using |:filter|
You are currently in line 1167. If you then use the CTRL-O command, the
-cursor is put in line 1154. This results in:
+cursor is put in line 1154. This results in: >
- jump line col file/text ~
- 2 1 0 some text ~
- 1 70 0 another line ~
- > 0 1154 23 end. ~
- 1 1167 0 foo bar ~
-
+ jump line col file/text
+ 2 1 0 some text
+ 1 70 0 another line
+ > 0 1154 23 end.
+ 1 1167 0 foo bar
+<
The pointer will be set at the last used jump position. The next CTRL-O
command will use the entry above it, the next CTRL-I command will use the
entry below it. If the pointer is below the last entry, this indicates that
@@ -1118,15 +1118,15 @@
that calling setpos() does not do this.
After the CTRL-O command that got you into line 1154 you could give another
-jump command (e.g., "G"). The jump list would then become:
+jump command (e.g., "G"). The jump list would then become: >
- jump line col file/text ~
- 4 1 0 some text ~
- 3 70 0 another line ~
- 2 1167 0 foo bar ~
- 1 1154 23 end. ~
- > ~
-
+ jump line col file/text
+ 4 1 0 some text
+ 3 70 0 another line
+ 2 1167 0 foo bar
+ 1 1154 23 end.
+ >
+<
The line numbers will be adjusted for deleted and inserted lines. This fails
if you stop editing a file without writing, like with ":n!".
@@ -1162,7 +1162,6 @@
1 462 36 eval.c <-- location X
>
<
-
Then, when yet another location Z is jumped to, the new location Y appears
directly after location X in the jumplist and location X remains in the same
position relative to the locations (X-1, X-2, etc., ...) that had been before
@@ -1172,7 +1171,7 @@
4 1260 8 mark.c <-- location X-2
3 685 0 eval.c <-- location X-1
2 462 36 eval.c <-- location X
- 1 100 0 buffer.c <-- location Y
+ 1 100 0 buffer.c <-- location Y
>
<
CHANGE LIST JUMPS *changelist* *change-list-jumps* *E664*